环氧施工方案.docx
- 文档编号:9980659
- 上传时间:2023-02-07
- 格式:DOCX
- 页数:34
- 大小:969.96KB
环氧施工方案.docx
《环氧施工方案.docx》由会员分享,可在线阅读,更多相关《环氧施工方案.docx(34页珍藏版)》请在冰豆网上搜索。
环氧施工方案
AFEpoxyCoatingMethodStatement
动物房环氧涂装施工方案
Designation
Nameprinted
Signature
Date
PreparedBy
Engineer
ReviewedBy
TechnicalManager
ApprovedBy
ProjectManager
Contents目录
1.InGeneral
工程概况
2.RequirementtoConcreteSubstrate
对混凝土基层的要求
3.TechnicalProposalandApplicationDescription
施工工艺及施工程序
4.QualityControlandAcceptance
质量控制和施工验收
5.Qualification
防腐公司资质证明
6.MethodStatement
施工组织设计
7.SafetyandHousekeeping
安全和文明施工
8.ProductDatasheet,MSDS,ChemicalResistanceTable
产品说明书,材料安全数据表,材料化学耐性表
第一章
InGeneral
工程概况
1.1Project项目:
1.2WorkingPlace施工部位:
1.3Owner业主:
1.4Location项目地点:
第二章
RequirementtoConcreteSubstrate
对混凝土基层的要求
防腐涂装性能的发挥及其服务寿命,与混凝土基层的性能和质量密切相关,其施工工艺与技术指标应该是在公司认可的技术条件下进行,建议如下:
2.1WaterBarrier/防水层
Anydensecoatingsystem,suchashighbuildpolyestercoatings,cannotwithstandrisingmoisturethroughtheconcreteslab.Suchrisingmoisturemightcauseblisteringinthecoatingsystem.Therefore,awaterbarrierhastobeconstructedunderneaththeconcreteslab.
混凝土浇筑前应构筑防水层,防止地下上升的潮气影响树脂地坪材料的固化甚至在使用期间破坏地坪涂层。
2.2CompressiveStrength/抗压强度
Thecompressivestrengthoftheconcretesubstrateforreceivinghigh
buildpolyestercoatingsystemshouldbenolessthan30N/mm2.
最低使用C30混凝土,即混凝土地面浇筑完毕28后的抗压强度必须大于30Mpa;
2.3SurfaceQuality/表面质量
Concreteslabwithoutscreedonthetopandfinishedbypowerfloatingishighlyrecommended.Thetensilestrengthoftheconcretesurfaceshouldbenolessthan1.5N/mm2.Theconcreteslabshouldcureforatleast28daysandthemoisturecontentshouldnotbehigherthan6%beforepolyestercoatingapplications.ThyssenKruppXervonisabletoofferpowderfloatingservice.
建议一次性浇筑到设计标高,使用抹平机进行原浆抹平(不铺设找平层),地坪涂装前,混凝土地面的表面抗拉强度必须大于1.5Mpa。
混凝土地面必须养护至28天以后,且经测试其基层含水量不得超过6%;
2.4Flatness/平整度
Asaprotectivecoatinglayer,thecoatingsystemisnotabletoimprovetheflatnessoftheconcretesubstrateessentially.Therefore,theflatnessoftheconcretesubstrateshouldachievethestandardofthedesignorrequirementofuse.
由于防腐涂装作为保护涂层不能改善混凝土表面的平整度,因此在施工前,混凝土基面平整度必须达到设计标准或者业主的使用要求;
第三章
TechnicalProposalandApplicationDescription
施工工艺及施工程序
TechnicalProposal技术方案
Pre-cleanthefloorsurface,degreaseagentwillbeusedwherenecessary.
清洁表面,必要时使用清洁剂出去表面油污;
Dothebasicdetectionofconcretebase,includingtheroughness,surfacehardness,tensilestrength,moisturecontent.
对混凝土基层做基本检测,包括平整度、表面硬度、抗拉强度、含水率等。
SurfacelaitanceandtoprovidesoundandroughsurfaceisremovedbyShot-blasting.
使用自动钢丸喷砂机进行表面处理,喷除混凝土表面浮浆层及松散结构,并提供坚实、粗糙的待涂装表面。
Effectofshot-blasting.
喷砂完成后的效果,提供足够的粗糙度,保证涂层的附着力
Grinderisusedfortheareawhereshot-blastingcouldn’ttouch.
-边角等喷砂机不能处理到的区域,使用小型电动工具配合集尘设备处理是必要的。
-Checkthefloorsurfacetensilestrengthbyusingpullofftestingequipmentwithcontrolledincreaseofforce(DYNAZ15)accordingtointernationalstandard.
根据国际标准,使用抗拉测试仪(DYNAZ15)检测混凝土表面的抗拉强度;
Themoisturecontentshouldnotbehigherthan6%beforeSikafloorPurCem24NandSikafloor264coatingapplications.
-在实施环氧自流平或聚氨酯砂浆自流平前需要检测地面含水率,确保低于6%;
-Cleanedbyvacuum.
-扫除残留的钢丸及灰尘,并真空吸尘;
-Coatingaccordingthedatasheetofthematerial.
-根据材料生产商提供的的规范,实施地坪涂装。
A1SikafloorPurCem24N
HeavyDutyPolyurethaneMortarSelf-leveling,Smooth&MattFinish
Nominal6mmCoatingThickness
重载聚氨酯砂浆自流平,平滑亚光面,约6毫米涂装厚
SystemComponents
系统组成
ProductionName
材料名称
Application
施工方法
Consumption
涂布率
SurfacePreparation
表面处理
Shotblasting
钢丸喷砂
Primer
底涂
SikafloorPurCem21N
Trowel
镘涂
2.0kg/m2
Topcoat
面涂
SikafloorPurCem24N
Trowel
镘涂
10.0kg/m2
Remarks:
备注:
施工步骤
1、Surfacepreparation:
Cuttingtheanchoringslotbywidth10mmdeep5mmwhichfromthelimited100mmandcuttingslotslikenetsallthearea.
基层准备:
离开各边角10cm处切割5mm宽10mm深的锚固槽并在全场进行网状切割以增强后续涂层的附着力
-
-
2、PrimerSikafloorPurCem21N
底涂SikafloorPurCem21N
Application:
TrowelbymetaltrowelaftermixingaccordingtothedatasheetforSikafloorPurCem21N.Consumptionis2.00KG/㎡,andbroadcastwettowet.
操作方法:
按照材料说明书将SikafloorPurCem21N搅拌均匀后,使用金属镘刀在预处理好的地表上镘涂一道底涂,涂布率:
2.00公斤/平方米,然后湿对湿抛撒石英砂,石英砂用量约0.50kg/m2
要求:
底漆应与混凝土地面充分结合达到一个封闭的涂层。
3、TopCoatSikafloorPurCem24N
面涂SikafloorPurCem24N
Application:
TrowelbymetaltrowelaftermixingaccordingtothedatasheetforSikafloorPurCem24N.In5minutes,defoamingbyspikeroller.Consumptionis10.00KG/㎡.
操作方法:
按照材料说明书将SikafloorPurCem24N搅拌均匀后,使用金属镘刀在预处理好的地表上镘涂一道面涂,并确保材料涂布均匀。
在材料静置5分钟后,使用消泡滚筒进行消泡。
涂布率:
10.00公斤/平方米。
A2Sikafloor264
HighBuildEpoxyCoatingSystem
Nominal1.0mmCoatingThickness
厚浆型环氧地坪,约1.0毫米厚度
SystemComponents
系统组成
ProductionName
材料名称
Application
施工方法
Consumption
涂布率
SurfacePreparation
表面处理
Grinding
研磨
Primer
底涂
Sikafloor161
+Sikadur505Q
Roller
滚涂
0.4kg/m2
0.4kg/m2
Topcoat
面涂
Sikafloor264
Trowel
镘涂
0.8kg/m2
Remarks
备注:
施工步骤:
1、PrimerSikafloor161
底涂Sikafloor161
Application:
TrowelbymetaltrowelaftermixingSikafloor161withquatzsandsaccordingtothematerialdatasheet.Consumptionis0.40KG/㎡.
操作方法:
按照材料说明书将环氧底涂Sikafloor161搅拌均匀后,按照比例加入石英砂并再次搅拌均匀。
使用金属镘刀在预处理好的地表上镘涂一遍底漆,涂布率(树脂):
0.40公斤/平方米。
要求:
底漆应与混凝土地面充分结合达到一个封闭的涂层,底涂干固后,对露底部位须进行补涂
2、TopcoatSikafloor264
面涂Sikafloor264
Application:
TrowelbymetaltrowelaftermixingSikafloor264accordingtothematerialdatasheet.In10minutes,defoamingbyspikeroller.Consumptionis0.80kg/㎡.
操作方法:
按照材料说明书将环氧面涂Sikafloor264搅拌均匀后,使用金属镘刀在环氧底涂上镘涂一遍环氧面涂。
静置10分钟后,使用消泡滚筒消除起泡。
涂布率:
0.80公斤/平方米。
A3Sikafloor29NPurcem+Sikafloor31NPurcem
PUScreedCoving,H=100mm,R=50mm
聚氨酯砂浆圆弧踢脚线,100毫米高,弧度30毫米
A4Sikafloor264
EpoxyCoving,H=100mm,R=30mm
环氧圆弧踢脚线,100毫米高,弧度30毫米
A5SikagardSkimcoatC+SikagardWallcoatN
CementitiousBasedPutty+WaterBasedEpoxyWallCoating
水泥基腻子+水性环氧墙面、吊顶涂装系统
SystemComponents
系统组成
ProductionName
材料名称
Application
施工方法
Consumption
涂布率
SurfacePreparation
表面处理
Grinding
打磨
Putty
腻子
SikagardSkimcoatC
Scratch
批刮
4.0kg/m2
Topcoat
×2coats
2道面涂
SikagardWallcoatN
Roller
滚涂
0.4kg/m2
Remarks:
备注:
施工步骤:
1、Surfacepreparation
基层处理
Application:
Providesoundandroughsurfacebyhandlegrinder.
操作方法:
使用手提磨机对墙面进行打磨处理至坚实的表面,并通过打磨获得充分的粗糙度。
2、PuttySikagardSkimcoatC
腻子SikagardSkimcoatC
Application:
Scratchtheputtyonthewallandsanditbysandpaper.
操作方法:
使用刮刀将SikagardSkimcoatC外墙腻子均匀地批刮到墙面上并收光。
干透后使用砂皮纸对表面不平整的地方进行打磨。
3、TopcoatSikagardWallcoatN
面漆SikagardWallcoatN
Application:
MixingSikagardWallcoatNaccordingtothematerialdatasheet.Rolleritonthewall.
操作方法:
按照产品使用说明书将水性环氧墙面材料SikagardWallcoatN搅拌均匀后,使用进口长毛滚筒均匀地将材料滚涂到墙面上。
要求:
滚涂须均匀且无遗漏。
A6EpoxyLaminate
EpoxyLaminateSystem,Nominal2mmCoatingThickness
环氧纤维布压层系统,约2毫米涂装厚度
SystemComponents
系统组成
ProductionName
产品名称
Application
施工方法
Consumption
涂布率
SurfacePreparation
表面处理
Grinding
打磨
PrimerCoat
底涂
Sikafloor161
Roller
滚涂
0.40kg/m2
Laminatelayer
玻璃纤维布压层
Sikafloor161
+2xGlassmat300g
+1xSurfaceFleece30g
LayandRoller
人工敷设
3.30kg/m2
+4.4m2/m2
+1.1m2/m2
TopCoat
面涂
Sikafloor264
Roller
滚涂
0.60kg/m2
Remarks:
Colours:
ApplicationDetails具体施工工艺
Sikafloor161EpoxyLaminateSystem西卡环氧纤维布系统
1Priming底漆施工
将Sikafloor161树脂加入固化剂充分搅拌均匀,使用长毛滚筒滚涂于待施工表面。
为了达到封孔效果,可适当加入石英砂填料,填料和树脂配比重量不超过1:
1.
2Allowatleast8hoursmax.72hoursforcuringbeforeapplicationoflaminate.
施工玻纤布压层前,须固化至少8小时,最多72小时。
3Laminationlayer玻纤布压层
8-72hourslaterwhentheprimeriscured.RollerapplySikafloor161Primerontheprimedsubstrate,placethefiberglassmatontothewetmaterialandthenrollfirmlywithsteelplaterollertoventilatetheair.Eachpieceofmatshouldhaveaminimum10cmoverlap.Thelaminationlayerhas1-2layersfiberglassmat(300gor450g)andonelayersurfacefleece(30g).
待底漆固化8-72小时后,首先将玻纤布粘接料Sikafloor161滚涂在底涂好的基面上,随即将玻纤布铺贴其上,然后用钢片滚筒压紧以避免空气进入,每片玻纤布至少有10CM的搭接,纤维布层需用到2层短切毡(300g)及1层表面毡(30g)。
4Allowatleast12hoursmax.72hoursforcuringbeforeapplicationoftopcoat
施工面涂前,须固化至少12小时,最多72小时。
5Topcoat面涂施工
ApplySikafloor264intwocoatsbyrollercrosswise,theconsumptionshouldbe0.6kg/m2intotaltoproduceauniformandfinetexturedsurface
十字交叉方式滚涂两道西卡环氧基树脂Sikafloor264于基面上,涂布率总共为0.60kg/m2。
以达到一个均匀、略带纹理的光洁表面。
第四章
QualityControlandAcceptance
质量控制和施工验收
Wewillperformtheapplicationinstrictaccordancetosystemproposalsandproductdatasheet.Applicationqualityisrealizedthroughthefollowingcontrolactivities.
我们将严格按照系统方案和产品说明书进行施工,并通过以下控制手段确保施工质量:
4.1Staff人员
Wewillmobilizeourorganizationwithexperiencedmanagementpersonnelandskilledoperators.
我们将为此项目配备经验丰富的施工管理人员和熟练的施工作业人员。
4.2Material材料
Delivering,storing,handling,mixingandapplicationofmaterialwillbecarriedoutaspermanufacturer’sinstructions.Checkpackage,productiondate,shelflife,regulatorydocumentofeachbatchofmaterialwhentheyarrivejobsite.Materialwhichfailstocomplytheaboverequirementwillberejected.Wewillusefixedandexperiencedoperatorstomixmaterial.
材料的运输、储存、搬运、搅拌和施工将严格按照材料商的指导说明进行。
每批材料抵达现场时,均要仔细察看包装、生产日期、储存期和必备的文件资料,如无法满足上述要求,现场将拒绝接收。
我们将使用有经验的专人进行材料搅拌。
4.3Substrateinspectionandpreparation基层检查和处理
Beforestartofapplication,thesubstratewillbethoroughlyinspectedtomakesurethatitmeetsrequirement
施工前,彻底检查基层,以确认其满足要求。
3
4
4.4Ambienceinspection环境检查
Beforeandduringapplication,theambientconditionsshouldbeinspected,recordedandobserved.Wewillnotproceedtheworkbeforeambientconditionsaremet.
施工前和施工过程中,应检查、记录,达不到环境要求不能进行施工。
4.5Applicationmachineandtools施工器具
Machinesandtoolsareinaccordancewithmanufacturer’sdirectionsandmaintainedinfunctionalstatus.Someequipmentwillhaveback-up.
施工器具符合材
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 施工 方案
![提示](https://static.bdocx.com/images/bang_tan.gif)