OTISSKY安装参数.docx
- 文档编号:3752799
- 上传时间:2022-11-25
- 格式:DOCX
- 页数:93
- 大小:74.14KB
OTISSKY安装参数.docx
《OTISSKY安装参数.docx》由会员分享,可在线阅读,更多相关《OTISSKY安装参数.docx(93页珍藏版)》请在冰豆网上搜索。
OTISSKY安装参数
MCS-TCBC
ListofInstallationParameters(TCBC或GECB板安装参数解释)
Copyright2013,OTISGmbH&Co.OHGBerlin.
NopartofthisdocumentmaybecopiedorreproducedinanyformorbyanymeanswithoutthepriorwrittenconsentofOTIS.
1–SYSTEM系统进入TCBC或GECB后(SVTM-1-3-1-1-GOON)
No.
Symbol
Default
PurposeandRange
since
1.
TOP顶楼
2
Topposition:
1
(1)31
2.
LOBBY大厅
0
Lobbyposition:
SeparatedoortimeLOB-NTcanbeusedatthelobby.
0
(1)31
3.
BOTTOM底楼
0
Bottomposition:
0
(1)30
4.
CFT-P餐厅
255
CafeteriaPosition:
SeparatedoortimeCFT-NTcanbeusedatthecafeteria
0
(1)31
>31Disabled设置大于31就不允许说功能
5.
OPERAT操作功能
1
OperationFCL/DCL/SAPB:
0全选FCL(FullCollective)
1下选DCL(DownCollective)
2一个SAPB(SingleAutomaticPushButton)
3一个多灯SAPBwithCarComingLight
4消号FCL,deletebothcallsonarrival
5全选一个安钮FCLwithsinglebuttonforbothdirections
6.
EN-BSM允许基站
0
EnableBasementmodeforDCL
(twoHallCallsatlobby(UpandDown):
0Disabled
1Enabled
7.
PI位置显示
4
TypeofserialPositionIndicator:
07/16Segment7和16段码
1SerialMultilightviaRIB
27Segment-PIandLM-PIviaRIB
3Brazilian10-Segment
4OTIS2000:
LCDandELD
5AustralianDotMatrix
(usesalsoIO975,976)
6AustralianDotMatrixandDirectionIndicator
(usesalsoIO975,976)
8.
PI-OPT
0
VendorPIoption层显功能
0nooption
1returningtogroundfloor
2overloaded
4outofservice
8liftonfirefightingservice
note:
ifmorethanoneoftheaboveoptionsshouldbeavailablethenyoumustaddtheappropriatenumbers
(e.g.toselect1+4youmustprogram5)
9.
PI-POS
显示板上数据信息类型
0
TypeofFloorInformationonPositionIndicator
0ActualFloor
(countedbyIP)
1NextCommitableFloor
(countedbyDZandIP)
2fallingedgeofDZ
3risingedgeofDZ
AAE
10.
ELD-fOPG
前门运动时间(开门)
20
frontdoormovementtime:
opening
Timethefrontdoorneedstoopen
0(0.1)10.0s
0=automatic(notyetimplemented)
Note:
CPI-11only(PI=4)
11.
ELD-fCLG
前门运动时间(关门)
20
frontdoormovementtime:
closing
Timethefrontdoorneedstoclose
0(0.1)10.0s
0=automatic(notyetimplemented)
Note:
CPI-11only(PI=4)
12.
ELD-rOPG
后门运动时间(开门)
20
reardoormovementtime:
opening
Timethereardoorneedstoopen
0(0.1)10.0s
0=automatic(notyetimplemented)
Note:
CPI-11only(PI=4)
13.
ELD-rCLG
后门运动时间(关门)
20
reardoormovementtime:
closing
Timethereardoorneedstoclose
0(0.1)10.0s
0=automatic(notyetimplemented)
Note:
CPI-11only(PI=4)
14.
ELD-LNG
ELD语言
5
setLanguageforELD:
0
(1)27
0=SwiGer,1=SwiFra,2=SwiIta,3=France,
4=Italy,5=UK,6=Spain,7=Netherlnd,
8=Germany,9=Austria,10=Sweden,11=Luxem,
12=Belgium,13=Portugal,14=Egypt,15=Denmark
16=SthAfrica,17=Finland,18=Arabia,19=Kuweit,
20=Moscow,21=StPetrbrg,22=notused,23=AGB,
24=Hungary,25=Poland,26=Czech,27=UKB
Note:
CPI-11only(PI=4)
15.
ELD-Sym1
允许不能吸烟标志
0
EnableNon-Smokingsymbol:
0NoSymbolonELD
1NoSmokingsymbolisdisplayed
Note:
CPI-11only(PI=4)
16.
ELD-DOOR
选择门的显示类型
0
SelectTypeofDoorDisplay:
0:
1COPfor1dooror一个操作板对应1门
2COPsfor2doors
(usedummyplugforrearELD)
1:
only1COPfor2doors一个操作板对应2门
Note:
CPI-11only(PI=4)
17.
ELD-MSG
允许显示乘客信息
0
EnablesCustomerMessagesonELD:
0nocustomermessagesaredisplayed
(existingcustomermessageswillbedeleted
atthenextPowerOn)
1customermessagesareenabled
ELDmustbereinitializedifthePosition
IndicatorSetupischanged
(useSETUP-ELDtodefinethetexts)
Note:
CPI-11only(PI=4)
18.
EN-SFR
允许信息过滤
0
EnableSFR(signalflicker):
启用方向箭头闪烁功能
Selectthattheoutputswillblink(insteadofbeingconstantlyilluminated)whenactivated:
0Disabled禁止
1singledevices允许
BUZ,EQL,ERL,FDL,FSL,HEL,INLC,
NSLC,OLS,PFL,CRFL,EFOL,EFOAL,
ARL,DUPL
19.
LR-T
灯继电器时间选”分”和”秒”
20
LightRelaytime(IO0026,PX2:
1):
AparkingcarwillswitchoffthecarlightafterLR-T.TheCPI-11(ELD)isalsoswitchedoffafterthistime.
0
(1)255secondsifLR-MODE=0,1
0
(1)255minutesifLR-MODE=2,3
Note:
LR-TisstartedafterthecarhasbecomeIDLE.AssoonasLR-ThasexpiredtheLRoutputisactivatedandtheELD(CPI-11)isswitchedtoSleep-Mode.
20.
LR-MODE
风扇/灯继电器选择模式
0
Fan/LightRelaymodeoption(IO0026,PX2:
1):
{0关门后动作LRpullsafterLR-Tseconds
onlywhendoorclosed(Light)
1}秒开门动作LRpullsafterLR-Tseconds
evenifdoorisopened(Fan)
{2LRpullsafterLR-Tminutes
onlywhendoorclosed(Light)
3}分LRpullsafterLR-Tminutes
evenifdoorisopened(Fan)
21.
EN-HLC
厅外显示
0
EnableHallLanternsoncarcalls:
允许到站灯响应内选信号
0对外有用Halllanternswilloperateonlyonhallcalls
1对内外有用Halllanternswilloperateonhallandcarcalls
2关门后也亮like0,butalsoduringdoorclosing
3关门后也亮like1,butalsoduringdoorclosing
22.
HDL-TYP
厅方向类型
0
HallDirection/LanternTypefor
OTIS2000HallButtonBox(IOs814ff,846ff):
0外呼显示DirectionIndicator
1到站灯HallLantern
23.
HL-SET
0
HallLantern/GongSetup:
外呼灯/光钟的设置
0LanternandGongatsamepins
1LanternandGongatdifferentpins(RS4A)
2NAOChimeboard
24.
CR-DIR寻址方向
0
CorrectionFastRunPreferredDirection:
0向下Down下行
1向上Up上行
25.
CR-DO寻址后状态
0
DooropeningafterCorrectionRun寻址运行后开门设置
0nodooropens不开门
1onlyfrontdooropens仅开前门
2onlyreardooropens仅后门开
3bothfrontandreardoorwillopen前后门都开
note:
AfterTCI/EROtheDO2000needsanewinitializationrun.NormallythedoorisnotopenedafterCORsothattheinitrunisdoneuponthefirstdemandwhichisusuallyahallcall.Thereforethepassengermightwonderabouttheslowdoormovement.
Withthisparameteryoucanselectthatthedooropensimmediatelyaftercompletionofacorrectionrun.Thedoormovementforthefirstdemandwillthenbedonewithanormaldoorprofile.仅用于DO2000,因为每次检修后要进行一次初始化运行
26.
ERO-TYP
ERO类型
0
DefineEROtype
0withoutlimit没有
1carstopsatterminallandings
(sameasTCI-limit)轿厢停在终端类式检修限位
27.
REM-TYP
0
TypeofinstalledREM
0REM-5
1REM-G
2REM-5(sameasREM-TYP=0)
Note:
REM-TYP=2hasbeenaddedforcompatibilitywithsimilarsoftwarebaselines.InthisbaselineREM-TYP=0andREM-TYP=2arethesame.
28.
CPC-TYP轿厢位置输出点(楼层输出信号)
selectuseofCPCoutputs:
0carpositioncontact在每层都有
Theoutputatalandingisswitchedonifthe
carisatthatlanding
(evenifthecarismoving)
1'carhere'light只要停就有信号
Theoutputatalandingisswitchedonifthe
carisatthatlanding
(onlyifthecarhasstopped)
2frenchSSM
3ArrivalHallLantern(AHL-2)
Theoutputatalandingisswitchedonifthe
carisatthatlanding
(onlyifthislandingisthetargetlanding)
29.
DFCR-DEL
DFC继电器的延迟时间
0
DelayforDFC-RelayDFC继电器的延时
0disabled
1
(1)255sdelayforwhichDFCRoutputiskeptactive
afterDFCinputhasbeenopened
Note:
ForModuleBDC
30.
LW-TYP称重类型
0
LoadWeighingTyp:
0carloadweighingviaCANbus(LWB_II,oranaloglwwithMCB_III)(GeN2-C/Cx)
1deadendhitchloadweighingviaCANbus(MCB_IIIxwithDynacellsensor)(GeN2-R)
2discretecarloadweighingviaremotestationinputs
254permanentOLDactive(onlyfortests,sinceAAC)
255disabled(preventsOLDforcodetests)
31.
PX2.1PX2.1输出口
0
selectuseofPX2.1output
0LRlightrelay/likeio026
1UDtripcounter/likeio805
AAC
32.
HWY-TYP井道类型
0
HoistwayTyp:
0normal正常选0
1lowoverhead(io1047,1048,1050,1054)
2shallowpit(io1049,1052,1055)
3lowoverhead&shallowpit(1+2)
AAD
2–OCSS(进入TCBC或GECB后按SVTM-1-3-1-2-GOON)
No.
Symbol
Default
PurposeandRange
since
1.
CPR-T设定内选优先时间
20
CarCallPreference:
Thisisthedurationforwhichcarcallshavepriorityoverhallcallsafterthedoorsareopened.Thisisusablee.g.forSingleAutomaticPushButton(SAPB)andDownCollectiveoperation(DCL).
0(0.1)25.5s
2.
ARD-P自动返回基站位置
255
AutomaticReturnDevicePosition:
Ifnofurthercallsarepending,thecarwillreturntothisfloorafterARD-Thasexpired.
0
(1)31
>31Disabled
Note:
Simplexonly
3.
ARD-T自动返回基站延迟时间
0
SetDelayforARD(AutomaticReturnDevice)mode:
0(10)2550s
4.
ARBL-T自动到底层的延迟时间(群控用)
0
DelayforAutomaticReturnToBottomLanding
ARBLmeansthatthecarmovestothelowestlandingafteraselectableperiodoftime.ThisParkRunisperformedevenforspecialOCSSmodesase.g.ISCorATT.
Italsoallowslobbyparking(ARD-T)inpresenceofbasementfloorswithoutdefeatingcoderequirements.
0(10)2540s
255disabled
Note:
ThisparametermustbelargerthanARD-Ttotakeeffect.
5.
ARBL-PRK返回到楼层的位置
0
ARBLparkoption
0stayatbottomafterARBLhasbeen
performed当ARBL启动时一直待在底层
1returntopreviousparklandingafterARBL
hasbeenperformed当ARBL启动时返回预设楼层
6.
PKS-P驻停位置
255
ParkandShutdownPosition:
ThecarmovestothislandingifPKSisoperated.AfteropeningandclosingofthedoorthecarisshutdownwithDOBenabled.
0
(1)31
>31Disabled禁止
7.
PKS–TYP类型
一般选0
0
ParkingShutoffType:
应答完所有呼梯后轿厢回到驻停位置之后停止
0Afterservingallpendingcarcalls,carwill
returntoPKSpositionandshutdown
afterPKS-Tseconds
1Sameasabove,butaftercararrivedatPKS
positionitcanbeswitchedtoISC同上,只是轿厢打到独立服务
2Like0,butcarwillshutdownwithdooropen同0轿厢停止,并且保持门开
8.
PKS-T
PKS达到设置时间后才休梯
0
ParkingShutoffTime:
锁梯时间
TimeafterwhichthecarisshutdownatPKS-P
0
(1)255s
9.
PKS-DO
PKS开门的类型
0
PKSdefaultdoor:
0开门BothdoorswillopenatPKS-P到驻停位置开两扇门
1开前门Onlyfrontdooropens只开前门
2开后门Onlyreardooropens只开后门
10.
EN-SHB
允许单独的大厅呼梯
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- OTISSKY 安装 参数