AMS2771B航空材料规范铝合金铸件的热处理.docx
- 文档编号:29903259
- 上传时间:2023-08-03
- 格式:DOCX
- 页数:25
- 大小:158.57KB
AMS2771B航空材料规范铝合金铸件的热处理.docx
《AMS2771B航空材料规范铝合金铸件的热处理.docx》由会员分享,可在线阅读,更多相关《AMS2771B航空材料规范铝合金铸件的热处理.docx(25页珍藏版)》请在冰豆网上搜索。
AMS2771B航空材料规范铝合金铸件的热处理
SAE海陆空机动性推进工程学会
AEROSPACEMATERIALSPECIFICATION
航空材料规范
AMS2771B
IssuedOCT19871987年10月出版
RevisedAUT20002000年8月修订
SupersedingAMS2771A代替AMS2771A
(R)HeatTreatmentofAluminumAlloyCastings
(R)铝合金铸件的热处理
1.SCOPE:
1.范围
1.1Purpose:
Thisspecificationcoverstheengineeringrequirementsforheattreatmentofaluminumalloycastingsandforpartsmachinedfromcastings.
1.1目的
本规范涵盖了铝合金铸件以及铸件加工而成的零件的热处理工程要求。
1.1.1MAM2771isthemetricversionofthisspecification.
1.1.1MAM2771是本规范的公制版本。
1.2Application:
1.2适用:
Thisspecificationisapplicabletocastingsofthefollowingaluminumalloysandmodifications.(See8.2.8)
本规范适用于如下铝合金铸件及其变型(见8.2.8)
201.0
203.0
206.0
222.0
242.0
243.0
295.0
296.0
319.0
328.0
333.0
336.0
354.0
355.0
356.0
357.0
358.0
359.0
520.0
SAETechnicalStandardsBoardRulesprovidethat:
“ThisreportispublishedbySAEtoadvancethestateoftechnicalandengineeringsciences.Theuseofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarisingtherefrom,isthesoleresponsibilityoftheuser.”
SAE技术标准委员会规则规定:
“本报告由SAE发布,用以推进技术及工程科学的状态。
使用本报告完全出于自愿,本报告如用于特殊用途,包括由此引起的任何专利侵权,由使用者负责。
SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhichtimeitmaybereaffirmed,revised,orcancelled.SAEinvitesyourwrittencommentsandsuggestions.
SAE至少每五年检查各技术报告,同时可能重审,修订,或取消。
SAE欢迎您的书面意见和建议。
Copyright2000SocietyofAutomotiveEngineers,Inc.
Allrightsreserved.
美国机动工程师协会版权所有2000
保留所有权利
QUESTIONSREGARDINGTHISDOCUMENT:
(724)772-7161FAX:
(724)776-0243
TOPLACEADOCUMENTORDER:
(724)776-4970FAX:
(724)776-0790
SAEWEBADDRESS:
http:
//www.sae.rog
若对本文献有疑问,请致电:
(724)772-7161FAX:
(724)776-0243
若要购买本文献,请致电:
(724)776-4970FAX:
(724)776-0790
SAE网站:
http:
//www.sae.rog
1.2(Continued):
1.2(续)
705.0
707.0
712.0
713.0
850.0
851.0
852.0
1.3WhenAMS2771isspecifiedandspecificheattreatprocessinginstructionsareincludedinthematerialspecification,theequipmentandcontrolrequirementsofAMS2771shallapply.Foralloysnotspecificallycovered,theprovisionsofthisspecificationshallbeapplicable,buttemperatures,times,andquenchingproceduresshallbespecifiedbythepurchaser.
1.3AMS2771规定了材料规范中包括热处理过程说明,应使用AMS2771设备和控制要求。
未明确涵盖的合金,本规范的条款应适用,但温度、时间和淬火工序应由买方确定。
2.APPLICABLEDOCUMENTS:
Theissueofthefollowingdocumentsineffectonthedateofthepurchaseorderformsapartofthisspecificationtotheextentspecifiedherein.Thesuppliermayworktoasubsequentrevisionofadocumentunlessaspecificdocumentissueisspecified.Whenthereferenceddocumenthasbeencanceledandnosupersedingdocumenthasbeenspecified,thelastpublishedissueofthatdocumentshallapply.
2.适用文献
如下文献的发布在买方的订单成为本规范的一部分之日起开始生效。
供应方应随后对文件作修改,除非已规定了明确的文件版本。
如果所参考的文献已被撤消,又未指定替代文献,应使用该文献的最后一次版本。
2.1SAEPublications:
2.1SAE出版物:
AvailablefromSAE,400CommonwealthDrive,Warrendale,PA15.96-0001.
SAE,400CommonwealthDrive,Warrendale,PA15.96-0001有售。
AMS2750Pyrometry
AMS2770HeatTreatmentofAluminumAlloyParts
AMS3025PolyalkyleneGlycolHeatTreatQuenchant
ARP1962TrainingandApprovalofHeat-TreatingPersonnel
AMS2750高温计
AMS2770铝合金零件的热处理
AMS3025聚氧化烷撑(PolyalkyleneGlycol)热处理淬火剂
ARP1962热处理的员培训及认可
3.TECHNICALREQUIREMENTS:
3.技术要求:
3.1Equipment:
3.1设备
EquipmentusedforthermalprocessingshallconformtotherequirementsofthisspecificationandAMS2750,except
(1)requirementsforworkingzonecontrols,instrumentsandsensorsshallapplytoallheatingzonesofcontinuousandsemi-continuousfurnacesand
(2)recordingsfrominstrumentsmaybestoredonmagneticoropticalmediaprovidingahardcopyisavailableonrequest.
用于热处理的设备应符合本规范和AMS2750的要求,除了
(1)工作区控制,仪器和传感器的要求应运用于所有连续和半连续冶金炉的加热区,并且
(2)仪器上的记录应保存于磁性介质或光学介质上,可按要求提供复印件。
3.1.1Pyrometry:
ShallmeettherequirementsofAMS2750.
3.1.1高温计:
应符合AMS2750的要求
3.1.2Furnaces:
3.1.2冶金炉:
3.1.2.1HeatingMedia:
Shallbeair,protectiveatmosphere,combustedgases,moltensaltbath,oilbath,offluidizedbed.Electricalheatingelementsandradianttubesshallbeshieldedtopreventdirectradiationfromstrikinganypart.Theproductsofcombustioninthefurnace,andthecompositionandmaintenanceofsaltbathsandfluidizedbedsshallbesuchastopreventattackorcontaminationoftheparts.Ammoniumfluoroborate,orequivalent,maybeusedinairfurnacesasnecessary.Nitratesaltbathsshallnotbeusedtoheattreat520.0alloyduetoapotentialexplosionsafetyhazard.
3.1.2.1加热介质:
应该为空气,保护性气氛,燃烧气体,熔融盐槽,油槽,流化床。
电子加热成分和辐射管应屏蔽,以防止直接辐射。
冶金炉中燃烧的产品,和盐池和流化床中的成分应防止零件腐蚀和污染。
必要时在空气炉中可使用氟硼酸铵或同类产品。
硝酸盐槽应用于520.0合金的热处理,因为可能影响安全的爆炸。
3.1.2.11SaltEntrapment:
Partthatwillentrapsaltshallnotbeheatedinamoltensaltbath.
3.1.2.11滞盐:
滞盐的零件不得在熔融盐槽中加热。
3.1.2.2TemperatureUniformitySurveyRequirements:
Afterstabilization,thetemperaturesofalltestthermocouplesshallbewithinthefollowingallowableranges(theserangessupersedethe±temperaturetolerancesspecifiedinAMS2750).
3.1.2.2温度均匀性测量要求:
等稳定后,所有测试热电偶的温度应处于如下的范围内(这些范围替代了AMS2750中规定的±温度公差)。
3.1.2.2.1SolutionHeatTreatingandAgingFurnaces:
Theallowablerangeis20℉forfurnacesusedforsolutionheattreatingoraging.
3.1.2.2.1溶解热处理和老化炉:
用于溶解热处理或老化的冶金炉温度公差范围为20℉。
3.1.2.2.2AnnealingFurnaces:
Theallowablerangeis50℉forfurnacesusedonlyforannealing.
3.1.2.2.2退火炉:
公差范围为50℉的冶金炉仅用于退火。
3.1.3Quenching:
Unlessotherwiseapprovedbythecognizantengineeringorganization,thefollowingprovisionsapply.Equipmentshallbeprovidedforquenchinginwater,airblast,oil,orinpolymerquenchantsandformeasuringquenchanttemperature.Provisionsshallbemadeformechanical,hydraulic,orairagitationofthequenchingmediumoragitationofthepartsorbothandforheatingandcoolingofthequenchant,asrequired.Airagitationshallbeallowedprovidedtheairdoesn’tcomeincontactwiththepartsbeingquenched.Thevolumeofquenchingmediumforimmersionquenchingshallbesufficientsothatitstemperatureriseduetoquenchingmeetstherequirementsof3.2.8.4.1.
3.1.3淬火:
除非由知名的工程机构另行规定,一般使用如下条款。
应提供水中淬火,空中鼓风,油,或聚合体淬火剂的设备,并测量淬火剂温度。
按要求提供淬火介质或零件搅动的机械,液压,或充气搅动,用于淬火剂的加热和冷却。
如果空气不进入与淬火中的零件接触,应允许进行空气搅动。
沉浸式淬火的淬火介质量应足够,以使其由于淬火达到3.2.8.4.1的要求时温度升高。
3.1.3.1PolymerQuenchants:
PolyalkaleneglycolshallmeettherequirementsofAMS3025.Othersyntheticsmaybeusedprovidedthattheyarenotdetrimentaltothematerialandthatthepartsmeettherequiredspecifiedpropertiesinthefinalheattreatedcondition.Polymerconcentrationshallbeestablishedfortheparticularcastingconfigurationpriortouse.
3.1.3.1聚合体淬火剂:
聚氧化烷撑应符合AMS3025的要求。
如果它们对材料无害,并且零件符合最终热处理条件所要求的特性,也可用其它合成材料。
在使用前应根据特定铸件构成,确定聚合体的浓度。
3.1.3.2SaltContaminationofPolymerQuenchants:
shallnotexceed6%byweight.
3.1.3.2聚合体淬火剂的盐污染:
重量上不得超过6%.
3.1.4Cleaning:
Equipmentshallbeprovidedtocleancastings,whennecessarybeforeheattreatment,andtoremoveresidualfilmfrompartsquenchedinapolymerquenchant,oilfrompartsquenchedoragedinoilbaths,andsaltresiduefromthesurfacesofpartsheatedinmoltensaltbaths,unlessthequenchbathisequippedwithfreshwateroverflow.
3.1.4清洗:
应提供清洗铸件的设备,用于热处理前必要的清洗,除去零件于聚合淬火剂中淬火后的残留膜,油槽中淬火或老化后残留的油,以及在熔融盐槽中加热后残留的盐,除非淬火槽安装有淡水冲淋器。
3.1.5Refrigeration:
Refrigerationorliquidbathsshallbeprovidedforcoldstorageofpartswhenpreventionofnaturalagingisnecessary.
3.1.5冷却:
应提供冷却箱或水槽,用于有必要防止自然老化的零件的冷藏。
3.2Procedures:
3.2步骤:
3.2.1General:
CastpartsthatrequireheattreatmenttoaT4X,T6X,orT7Xtempershallbesolutionheattreated(includingquenching),refrigeratedafterquenching,whennecessary,andaged,whenrequired,asspecifiedherein.CastingsintheT5Xconditionshallberefrigeratedaftercasting,whennecessary,andagedasspecifiedherein.Heattreatmentshallbeperformedonlyonentireparts,neveronaportionofapart.
3.2.1概述:
需要热处理至T4X,T6X或T7X回火的浇铸零件应溶液热处理(包括淬火),如有必要的话,淬火后冷却,如有需要的话,老化,如此处所说明。
T5X条件下的铸件有必要的话,在浇铸后应冷却,并按此处所述进行老化。
热处理只可对整个零件进行,不得对零件的一部分进行。
3.2.2RackingandSpacing:
Productshallbesupportedorhungandspacedtopermitflowoftheheatingandcoolingmediaoverallsurfacestoensurethatthecastingswillmeetthespecifiedrequirements.Alternaterackingmethodsareacceptableiftestshavebeenperformedtodemonstratethatallcastingssorackedwillmeetspecifiedrequirements.Writteninstructions,drawings,photographs,etc.shallbeusedtoensureproperspacing.
3.2.2支架和间距:
产品应适当放置或悬挂,其间隔应容许加热或冷却介质流过所有表面,以确保铸件符合规定的要求。
如果已进行过测试,表明其它方式堆放的铸件符合规定的要求,则可接受该堆放方式。
应使用书面说明,图纸,照片等确保正确的间隔。
3.2.2.1Smallpartsasdefinedin8.2.4maybeheatedandsoakedinbasketsorcontinuousfurnaces.Caremustbeusedtoprovideaccessforheatingandquenchmediaandtopreventdamageduringloadingandquenching.Arrangementinbasketsmaybeeitherorderlyorrandomprovidedthatthepartsmeettherequiredspecifiedpropertiesinthefinalheattreatedcondition.
3.2.2.0如8.2.4中所定义的小零件可以在筐中或连续冶金炉中加热或浸泡。
接近加热和淬火介质进应小心,避免在存放和淬火时损坏。
在筐中可以整齐放置或随意放置,只要零件符合最终热处理条件所要求的特性。
3.2.2.2WaterEntrapment:
Racksandfixturesusedforsolutionheattreatmentshallbeconstructedtoprecludeentrapmentofwater.
3.2.2.2滞水:
用于溶液热处理的架子和装置的构造应有利于排水。
3.2.3Loading:
Thetemperatureofthefurnaceduringpartloadingshallnotexceedthesolutiontreatingtemperatureofthepartsbeingheattreated.
3.2.3装载:
在零件装载过程中,冶金炉的温度不应超过正在热处理的溶液处理温度。
3.2.4SetTemperature:
Controlinstrument(s)shallbesetatthetemperaturespecifiedin3.2.8forsolutiontreatingand3.2.10foraging,andshouldbesetattherecommendedannealingtemperaturespecifiedin3.2.11.Sensor/controloffsets,ifused,shallcomplywithAMS2750.
3.2.4设定温度:
控制仪器的溶液处理应设定至如3.2.8所规定的
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AMS2771B 航空 材料 规范 铝合金 铸件 热处理