SRTG08 油系统冲洗方案oil flushing58.docx
- 文档编号:29792561
- 上传时间:2023-07-27
- 格式:DOCX
- 页数:15
- 大小:35.09KB
SRTG08 油系统冲洗方案oil flushing58.docx
《SRTG08 油系统冲洗方案oil flushing58.docx》由会员分享,可在线阅读,更多相关《SRTG08 油系统冲洗方案oil flushing58.docx(15页珍藏版)》请在冰豆网上搜索。
SRTG08油系统冲洗方案oilflushing58
1×15MWSEMIRARACOALFIRED
POWERPLANTPROJECT
INSTRUCTIONS
FOR
OILFLUSHING
C
B
A
0
FIRSTISSUE
REV.
SIGNATURE
DATE
WRITTEN
DATE
CHECKED
DATE
APPROVED
DATE
REVISIONNO.:
0
PAGE:
1OF13
TITLE:
油系统冲洗方案/InstructionforOilFlushing
FILENO.:
SR-TG-08
目录
TableofContents
1设备及概况EquipmentandOverview1
2油循环前具备条件ConditionsProvidedbeforeOilCirculation1
3油循环步骤OilCirculatingSteps4
4油系统冲洗的清洁度评定EvaluationofCleanlinessofFlushedOilSystem8
5后续工作EvaluationofCleanlinessofFlushedOilSystem9
6安全施工SafetyConstruction10
7临时系统材料表MaterialListofTemporarySystem11
1设备及概况EquipmentandOverview
菲律宾塞米拉拉项目1×15MW机组采用杭州汽轮机厂制造的NK40/56/25型汽轮机,南阳防爆集团股份有限公司生产的QFW-15-4型汽轮发电机,冲洗的范围包括:
润滑油系统和部分控制油系统。
THE1X15MWSEMIRARACFBPOWERPLANTPROJECTusesNK40/56/25steamturbinegeneratorsmanufacturedbyHANGZHOUSTEAMTURBINECO.,LTD,andQFW-15-4steamturbinegeneratorsmanufacturedbyNANYANGEXPLOSIONPROTECTIONGROUPCO.,LTD.ofwhichtheflushingscopeincludes:
lubricatingoilsystemandpartofcontroloilsystem.
2油循环前具备条件ConditionsProvidedbeforeOilCirculation
1)所有碳钢材料的管道和管件,必须经过酸洗。
辅助油箱打磨temperarytank20m3
1)Allcarbonsteelpipesandfittingsshouldbesubjectedtoacidpickling.
2)所有不锈钢材料的管道和管件,油循环之前,必须经过严格吹扫(最好蒸汽吹扫),且吹扫后采取特殊措施,用干净的绸布对管道内部进行擦洗。
完成后对内壁进行检查。
必须没有灰尘,管壁清洁
2)Allstainlesssteelpipesandfittingsmustbepurgedwithcompressedairpriortoinstallationandprotectedbytakingspecialmeasuresafterpurging,whiletheinsideofthemmustbecleanedbywipingwithcleanrag.
3)主油箱的清扫:
把油箱内部彻底清扫干净,先用白布,然后再用面团。
在油箱底部和回油的处加装磁棒。
3)Maintankcleaning:
thetankmustbethoroughlycleanedinsidewithawhiteclothfirstandthendough.Thebarmagnetsmustbeinstalledatthetankbottomandthescavengefilterscreen.
4)在汽机房安装二台LY-150压力式滤油机(含5000张滤油纸300mm×300mm),进口接主油箱疏油口一次门门前,出口接在主油箱人孔门上并联在主油箱上。
4)ALY-150pressureoilfilter(containing5000filterpapers,300mmx300mm)istobeinstalledat0mintheturbinegeneratorroomwiththeinletconnectedtothemaintankinfrontoftheprimarydoorofoleophobicoutlet,andtheoutletconnectedtothemaintankmanholedoorandtothemaintankinparallel.
5)汽轮机和发电机轴承:
将所有支持轴承上半部均拆除,支撑轴承下半部不动,推力轴承的推力板拆除。
5)Turbineandgeneratorbearings:
removetheupperhalvesofallsupportbearingswiththeirlowerhalvesremainedinoriginalpositions,andremovethethrustplatesofthrustbearings.
6)润滑油系统:
将润滑油管道与轴承座脱开,将进回油管用临时短管连接起来,在主油泵吸入口和出口处加堵板。
6)Lubricatingoilsystem:
theoilpipesaredisconnectedfromthebearingseats,theinletandreturnoilpipesareconnectedtogetherwithatemporaryshorttube.Addblindplateonsuctioninletandoutletofmainoilpump.
7)控制油系统:
速关组件进回油管用临时管道连接起来。
7)Controloilsystem:
theinletandreturnpipesofquickclosingassemblyareconnectedtogetherwithatemporarytube.
8)上油前的系统检查:
油箱上油前必须会同热工共同检查,确认系统连接正确无误,各热工测点安装正确无遗漏,油箱油位指示器灵活,其指示与油箱中的实际油位应相符合,做好防尘、防溅、防漏措施。
除必要的压力、温度监测点外,油系统其它仪表点应隔离。
8)Systemcheckbeforeoilsupply:
theoiltankmustbejointlycheckedwithaI&Cengineerbeforestartingoilsupplytoconfirmthatthesystemconnectioniscorrect,thethermalmeasurementpointsareinstalledcorrectlyandcompletely,andthetankoillevelindicatorissensitivewheretheindicationshouldbeconsistentwiththeactualoillevelinthetank;thesystemshouldbeprotectedbytakingpropermeasuresofdust,splashandleakageprevention.Inadditiontothenecessarypressureandtemperaturemonitoringpoints,theotherinstrumentpointsoftheoilsystemshouldbeisolated.
9)各油泵的电动机及系统上的排烟风机经过空载试运行情况正常。
9)Theoilpumpmotorsandtheexhaustfanonthesystemarecommissionedinnormaltestrun.
10)确信事故排油系统连接正确,各放油门关闭严密并挂警告牌禁止操作。
10)Makesurethattheemergencyoildrainsystemisproperlyconnected,thedrainersareclosedtightlyandthewarningsigns“OperationisProhibit”areattached.
11)确信直流电源能满足直流泵连续运行。
11)MakesurethattheDCpowersupplycanmeettheneedforcontinuousoperationofDCpump.
12)落实油箱加热装置,保证在连续冲洗过程中能把油从常温多次加热至75℃。
油加热时,油温不得高于80℃,以免油变质。
12)Theoiltankheatingdeviceiswellinstalledtoensurethattheoilisrepeatedlyheatedto75°Cfromroomtemperatureduringcontinuousflushing.Theoiltemperatureshallnotbehigherthan80°Cwhenheatingoil,toavoidthedeteriorationofoil.
13)冷油器放油口接临时管路,将油排至油箱,以免污积留在冷油器内。
13)Theoildrainoftheoilcoolerisconnectedtoatemporarytubetodraintheoilintothetank;toavoidthedirtaccumulatesintheoilcooler.
14)润滑油和调节油有各自的滤油器时,滤油器的滤芯拆出,在一个油冲洗循环周期后,再装入。
14)Whenthereareoilfiltersforlubricatingoilandregulatingoil,respectively,theoilfilterelementmustberemovedandtheninstalledafteraperiodofoilflushingcycle.
15)盘车油管路:
采用液压直行程盘车机构的,盘车油泵的进油由临时管路接至回油。
15)Barringoilpipe:
asthehydrauliclinear-motionbarringmechanismisused,theinletoilofthebarringpumpisconnectedtothereturnoilwithatemporarytube.
16)电液转换器不参与油冲洗。
装在速关组件上的电液转换器,闷板反装,有凹槽的一面朝向速关组件本体。
16)Theelectro-hydraulicconverterdoesn’tinvolveintheoilwashing.Theelectro-hydraulicconverteronthequickclosingassemblyisinstalledwiththeblankingflangemountedreverselyandthegroovedsidefacingthequickclosingassemblybody.
3油循环步骤OilCirculatingSteps
1)油箱上油TankOilSupply
油箱上油前,在确认油箱放油阀关闭正确,并采取了一定的防范措施,即可向油箱缓慢上油,上油时检查各管道连接处是否漏油,如有漏油修复后再继续上油,油箱距离油箱顶部约100mm时,停止上油,润滑油牌号ISOVG46汽轮机油,注油量约9m3。
注油时用滤油机或经过滤网注入,禁止直接倒灌。
灌油或放油时,储存汽轮机油的容器应清洁,不得使用盛过其它油品而未作彻底清理的容器,装油和运油时要防止与其它油品容器混淆。
Makesurethattheoildrainvalveofthetankisproperlyclosedandcertainpreventivemeasuresaretakenbeforestartingoilsupply.Starttofilloiltankslowly,checkleakageofconnectingpipesduringfilling,repairpipesifthereisanyleakageandthenoilfillingagain.Stopfillingastheoilinthetankis100mmlowerthantopoftank;theoilfilledshouldbeturbineoilofISOVG46,andtheoilquantityshouldbeabout9m3.Theoilshouldbefilledwithanoilfilterorthroughanoilfilterscreen;thedirectpouringisprohibited.Whenfillingordischargingoil,theturbineoilstoragecontainershouldbeclean;theuseofacontainerthathasbeenfilledwithotherbrandofoilandnotthoroughlycleanedupisprohibited;theoilloadingandtransportingshouldpreventtheoilcontainerfrommixingwithothers.
2)第一阶段油冲洗:
润滑油管路
Firstphaseofoilflushing:
oilpipes
流程为:
主油箱→辅助油泵(交、直流事故油泵可同时投入运行)→双联冷油器→双联滤油器(润滑油)→润滑油进油母管→各轴承处进油支管→各轴承处进回油管路临时短接→各轴承处回油支管→回油母管→主油箱
Process:
maintank→auxiliarypumps(ACandDCemergencypumpscanoperateatthesametime)→double-connectionoilcooler→double-connectionfilter(oil)→mainoilinletpipe→oilinletmanifoldsatbearings→temporaryshorttubesforoilsupplyandreturnatbearings→oilreturnmanifoldsatbearings→mainoilreturnpipe→mainoiltank
启动辅助润滑油泵(交、直流事故油泵可同时投入运行),同时用透明夹丝软管将压榨式滤油机串联在主油箱上在线滤油,冲洗24小时,冲洗油压尽可能接近系统工作压力;冲洗油温,应使油温冷、热交替变化,以8小时为1个循环周期,期间低温约25℃,高温约75℃。
Starttheauxiliaryoilpumps(ACandDCemergencypumpscanstartoperatingatthesametime)whileuseatransparentwiredhosetoconnectthepress-typeoilfilterinseriestotheonlineoilfilterinthemaintanktoflushfor24hourswiththeflushingoilpressureasclosetothesystemworkpressureaspossible;theflushingoiltemperatureshouldmaketheoiltemperaturealternatebetweencoldandhotmodeswithanintervalof8hourswherethelowtemperatureisapproximately25°Candthehightemperatureisapproximately75°C.
停辅助润滑油泵和交、直流事故油泵,用压差式滤油机将主油箱的油倒入已清理干净的储备油箱,然后把油箱和润滑油滤网清理干净。
这样进行反复冲洗,直到油质合格。
StoptheauxiliaryoilpumpsandAC&DCemergencyoilpumps,useadifferentialpressureoilfiltertopourtheoilfromthemaintankintothereservetankthathasbeenthoroughlycleaned,andthencleantheoiltankandoilfilterscreen.Sorepeatedlyflushuntiltheoilisqualified.
3)第二阶段油冲洗:
控制油管道Secondphaseofoilflushing:
controloilpipes
流程为:
主油箱→辅助油泵→双联滤油器(控制油)→速关组件前的进油母管→速关组件进回油临时短接→速关组件回油母管→主油箱
Process:
maintank→auxiliarypumps→double-connectionoilfilter(controloil)→mainoilinletpipebeforequickclosingassembly→temporaryshorttubesforoilinletandreturnofquickclosingassembly→mainoilreturnpipeofquickclosingassembly→mainoiltank
启动辅助润滑油泵,同时用透明夹丝软管将压榨式滤油机串联在主油箱上在线滤油。
冲洗24小时,冲洗油压尽可能接近系统工作压力;冲洗油温,应使油温冷、热交替变化,以8小时为1个循环周期,期间低温约25℃,高温约75℃。
Starttheauxiliaryoilpumpswhileuseatransparentwiredhosetoconnectthepress-typeoilfilterinseriestotheonlineoilfilterinthemaintank.Flushfor24hourswiththeflushingoilpressureasclosetothesystemworkpressureaspossible;theflushingoiltemperatureshouldmaketheoiltemperaturealternatebetweencoldandhotmodeswithanintervalof8hourswherethelowtemperatureisapproximately25°Candthehightemperatureisapproximately75°C.
停辅助润滑油泵,用压差式滤油机将主油箱的油倒入已清理干净的储备油箱,然后把油箱和润滑油滤网清理干净。
这样进行反复冲洗,直到油质合格。
Stoptheauxiliaryoilpumps,useadifferentialpressureoilfiltertopourtheoilfromthemaintankintothereservetankthathasbeenthoroughlycleaned,andthencleantheoiltankandtheoilfilterscreen.Sorepeatedlyflushuntiltheoilisqualified.
4)第三阶段油冲洗:
润滑油管路Thirdphaseofoilflushing:
oilpipes
第二阶段油循环结束后,润滑油系统,临时管道拆除,正式系统恢复,滤油器装入滤芯。
Afterthesecondphaseofoilcirculationiscompleted,removethetemporarytubesfromthelubricatingsystem,restorethesystemoperationandinstallthefilterelementintotheoilfilter.
启动辅助润滑油泵(交、直流事故油泵可同时投入运行),同时用透明夹丝软管将压榨式滤油机串联在主油箱上在线滤油,冲洗24小时。
滤油器滤芯定时清洗滤网,若规定时间未到,但进、出口油压差接近允许上限值时,应立即对滤油器进行切换清洗。
Starttheauxiliaryoilpumps(ACandDCemergencypumpscanstartoperatingatthesametime)whileuseatransparentwiredhosetoconnectthepress-typeoilfilterinseriestotheonlineoilfilterinthemain
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SRTG08 油系统冲洗方案oil flushing58 系统 冲洗 方案 oil
![提示](https://static.bdocx.com/images/bang_tan.gif)