锂电池组规格书范本.docx
- 文档编号:28767303
- 上传时间:2023-07-19
- 格式:DOCX
- 页数:12
- 大小:39.85KB
锂电池组规格书范本.docx
《锂电池组规格书范本.docx》由会员分享,可在线阅读,更多相关《锂电池组规格书范本.docx(12页珍藏版)》请在冰豆网上搜索。
锂电池组规格书范本
深圳市XXXXXX股份有限公司
LiBATTERYSPECIFICATION
锂离子电池规格书
Model
产品型号
4S1P-IFR17513545-12.8V-100Ah
Specification规格书编号
SM-QS-PE-CXKRK04
Materialcode
物料代码
Version
版本
A0
Revision
发行日期
2018-11-20
PreparedBy/Date
拟定
CheckedBy/Date审核
ApprovedBy/Date批准
CustomerSignature
客户回签栏
PreparedBy/Date
承认
CheckedBy/Date
审核
ApprovedBy/Date
批准
CompanyName:
公司名称:
CompanyStamp:
客户印章:
SHENZHENMOTTCELLNEWENERGYTECHNOLOGYCO.,LTD
Tel:
+86-755-XXXXXXX
Fax:
+86-755-XXXXXXX
AmendmentRecords
(修正记录)
Edition
(版本)
Description
(记述)
Preparedby
(编制)
Approvedby
(批准)
Date
(日期)
A0
FirstEdition
1.
Scope(使用范围)
ThisspecificationisappliedtothereferencebatteryinthisSpecificationandmanufacturedbySHENZHENMOTTCELLNEWENERGYTECHNOLOGYCO.,LTD.
本规格书适用于本书中所提及的深圳市山木新能源科技股份有限公司制造的电池。
2.DescriptionandModel(定义)
2.1Description(类型)
Lithiumironphosphatebattery(磷酸铁锂电池)
2.2Model(型号)
4S1P-IFR17513545-12.8V-100Ah
3.ProductSpecification(产品技术规格)
No.
(序号)
Item
(项目)
GeneralParameter
(常规参数)
Remark
(备注)
1
RatedCapacity
(额定容量)
标称容量(Typ.)100Ah
StandardchargeandStandarddischarge(标准充放电)(充电电流5A)
最小容量(Min.)96Ah
2
NominalVoltage
(标称电压)
12.8V
3
EndofChargeVoltage
(充电最高电压)
14.6V
4
Chargemode
充电方式
CC,CV
恒流、恒压
5
Chargingcut-offcurrent
充电截止电流
0.02C
6
Chargingtime
充电时间
20-22h
7
Over-ChargeVoltageProtection(cell)
充电单体电池保护
3.9V
8
Maxcontinuouschargecurrent
最大持续充电电流
5A
9
MaximumContinuousDischargingCurrent
持续最大工作电流
7A
Continuousthetable1(续表1)
No.
(序号)
Item
(项目)
GeneralParameter
(常规参数)
Remark
(备注)
10
Over-dischargeVoltageProtection(cell)
放电单体电池保护
2.4V
11
Over-CurrentDischargeProtection过流保护
15A
12
Shortcircuitprotection
短路保护
AnyProtection
有保护
13
ShortcircuitprotectionRelease短路保护恢复
Disconnecttheload
断开负载
14
CellDimension(尺寸)
Long(长)=MAX:
mm
结构尺寸详见第8页
(产品结构图)
Wide(宽)=MAX:
mm
High(高)=MAX:
mm
15
Weight(重量)
≈22Kg
16
OperationTemperatureRange(工作温度范围)
Charge(充电):
0~45℃
60±25%R.H.BareCell
(单体电池储存湿度范围)
Discharge(放电):
-10~60℃
17
StorageTemperature
Range(储存温度范围)
1month(一个月):
-20℃~45℃
3month(三个月):
-20℃~45℃
1year(一年):
-20℃~25℃
60±25%R.H.attheshipmentstate(出货状态时的湿度范围)
18
CycleLife
(循环寿命)
1.Charge:
5Ato14.6V
2.Constantvoltageto0.02CResttime:
10min
3.Discharge:
7Ato9.6V
4.RestTimebetweenChargeandDischarge:
10min
5.Temperature:
25±5℃
1.充电:
5A充至14.6V
2.恒压至0.02C,搁置10min
3.放电:
7A放至9.6V
4.搁置:
10min
5.温度:
25±5℃
Higherthan70%oftheInitialCapacitiesoftheCells
1000次≥初始容量70%
4.PerformanceAndTestConditions(电池性能及测试条件)
●StandardTestConditions(标准测试条件)
testandmeasurementshallbedoneundertemperatureof25±5℃andrelativehumidityof45~48%.
测试会在温度25±5℃,相对湿度在45-85%的条件下进行。
●MeasuringInstrumentorApparatus(测量器具及设备)
①DimensionMeasuringInstrument(尺寸测量器具)
Thedimensionmeasurementshallbeimplementedbyinstrumentswithequalormoreprecisionscaleof0.1mm.
尺寸测量器具的精度等级应不小于0.1mm。
②Voltmeter(伏特计)
Standardclassspecifiedinthenationalstandardormoresensitiveclasshavinginnerimpedancemorethan10kΩ/V.
按照国家标准指定规格等级或采用灵敏度更高的,测量电压时内阻不应小于10kΩ/V。
③Ammeter(安培计)
Standardclassspecifiedinthenationalstandardormoresensitiveclass.Totalexternalresistanceincludingammeterandwireislessthan0.01Ω.
按照国家标准指定规格等级或采用灵敏度更高的,包括电流表及电线在内的总外阻应小于0.01Ω。
④ImpedanceMeter(电阻计)
Impedanceshallbemeasuredbyasinusoidalalternatingcurrentmethod(1kHzLCRmeter)
内阻测试仪测量原理应为交流阻抗法(1kHzLCR)。
●StandardCharge/Discharge(标准充放电)
①Standardcharge:
Testprocedureanditscriteriaarereferredasfollows:
标准充电:
测试过程即标准如下:
5A=Chargingshallconsistofchargingat5Aconstantcurrentrateuntilthecellreaches14.6VThecellshallthenbechargedatconstantvoltage0f14.6Vwhenthechargingcurrenthastaperedto0.02C.Chargetime:
Approx20-22h,
电池先5A恒流充至14.6V,再以14.6V恒压充至电流减小到0.02C,充电时间大约为20-22个小时
②StandardDischarge(标准放电)
7A=Cellsshallbedischargedataconstantcurrentof7Ato9.6volts@25℃±5℃.
电池以7A恒流放电至欠压保护9.6V,@25℃±5℃。
③Ifnootherwisespecified,theresttimebetweenChargeandDischargeamountto30min.
如果没有特别说明,电池充放电间隔时间为30分钟。
●Appearance(外观)
Thereshallbenosuchdefectasflaw,crack,rust,leakage,whichmayadverselyaffectcommercialvalueofbattery.
电池外观应没有划痕、破裂、污迹、生锈、漏液等影响市场的缺陷存在。
5.Warning(电池注意事项)
●Prohibitionshortcircuit(禁止电池短路)
●NoticeforDesigningBatteryPack(电池外壳设计注意事项)
Packtoughness(外壳坚韧度)
BatterypackshouldhavesufficientstrengthandtheLi-Fecellinsideshouldbeprotectedfrommechanicalshocks.
电池外壳应该有足够的机械强度,使锂电池免受机械撞击。
Cellfixing(电池的固定)
TheLi-Fecellshouldbefixedtothebatterypackbyitslargesurfacearea.
Nocellmovementinthebatterypackshouldbeallowed.
电池最大面积的一面应该固定在外壳上,安装后电池不能有松动。
Tabconnection(极片连接)
SpotweldingisrecommendedforLi-Fetabconnectionmethod.
BatterypackshouldbedesignedthatshearforcearenotappliedtotheLi-Fetabs.
锂电池的极片采用点焊的方式。
电池组在设计时,锂电池极片不能承受剪切力。
●Prohibitionofdisassemble(禁止拆卸)
1)Neverdisassemblethecells
Thedisassemblingmaygenerateinternalshortcircuitinthecell,whichmaycausegassing,firing,explosion,orotherproblems.
不要拆卸电池。
拆卸电池会发生电池内部短路,会引起起火、爆炸、有害气体或其它问题。
2)Electrolyteisharmful(电解液是有害的)
Li-Febatteryshouldnothaveliquidfromelectrolyteflowing,butincasetheelectrolytecomeintocontactwiththeskin,oreyes,physiciansshallslushtheelectrolyteimmediatelywithfreshwaterandmedicaladviceistobesought.
锂电池不能有电解液流出,但在电解液接触皮肤,或眼睛时,应当立即用淡水冲洗,并且遵循医疗建议。
●Prohibitionofdumpingofcellsintofire(不要把电池浸泡于火中)
Neverincineratenordisposethecellsinfire.Thesemaycauseexplosionofthecells,whichisverydangerousandisprohibition.
不要把电池浸泡在液体当中,像清水、海水及非酒精饮料、果汁、咖啡或其它的饮料中。
●Batterycellsreplacement(更换电池)
Thebatteryreplacementshallbedoneonlybyeithercellssupplierordevicesupplierandneverbedonebytheuser.
更换电池应由电池生产商或设备供应商完成,用户不用自行更换。
●Prohibitionofuseofdamagedcells(禁止使用损坏的电池)
Thecellsmightbedamagedduringshippingbyshock.Ifanyabnormalfeaturesofthecellsarefoundsuchasdamagesinaplasticenvelopofthecell,deformationofthecellpackage,smellingofanelectrolyte,anelectrolyteleakageandothers,thecellsshallneverbeusedanymore.
Thecellswithasmelloftheelectrolyteoraleakageshallbeplacedawayfromfiretoavoidfiringorexplosion.
电池可能在出货途中碰撞而受损。
如果发现电池有异常,例如包装损坏、包装包裹变形,有电解液的味道、发现漏液等等,不要再使用这些电池如果有电解液的味道或出现漏液,电池放置应该远离火源避免起火爆炸。
●PeriodofWarranty(保质期)
Theperiodofwarrantyisoneyearfromthedateofshipment.Mottcellguaranteestogiveareplacementincaseofcellswithdefectsprovenduetomanufacturingprocessinsteadofthecustomerabuseandmisuse.
电池的保质期从出货之日算起为一年。
如果证明电池的缺陷是在制造过程中形成的而不是由于用户滥用及错误使用造成,本公司负责退换电池。
●StoringtheBatteries(电池的存放)
Thebatteriesshouldbestoredatroomtemperature,chargedtoabout30%to50%ofcapacity.
Werecommendthatbatteriesbechargedaboutonceperhalfayeartooreventoverdischarge.
电池应当在温室下存放,应充到30%至50%的电量。
如长时间储存,建议每半年充一次电,以防止电池过放电。
●OtherTheChemicalReaction(其它的化学反应)
Becausebatteriesutilizeachemicalreaction,batteryperformanceovertimeevenifstoredforalongperiodoftimewithoutbeingused.Inaddition,ifthevarioususageconditionssuchascharge,ambienttemperature,etc.arenotmaintainedwithinthespecifiedrangesthelifeexpectancyofthebatterymaybeshortenedorthedeviceinwhichthebatteryisusedmaybedamagedbyelectrolyteleakage.ifthebatteriescannotmaintainachargeforlongperiodsoftime,evenwhentheyarechargedcorrectly,thismayindicateitistimetochangethebattery.
由于电池是利用化学反应的原理,所以随时间的增加电池的性能会降低,即使是存放很长一段时间而不使用。
如果使用条件如充电、放电及周围环境温度等情形不在指定的使用范围内,会缩短电池的使用寿命,或者会产生漏液导致设备损坏。
如果电池长时间不能充电,即使充电方法正确,就要更换电池了。
●Note:
(注释)
Anyotheritemswhicharenotcoveredinthisspecificationshallbeagreedbybothparties.
本说明书包括事项应由双方协议确定。
Annex1(Productstructurediagram)附页(产品结构图)
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 锂电池 规格书 范本