船舶制造英语日常用语.docx
- 文档编号:2791572
- 上传时间:2022-11-15
- 格式:DOCX
- 页数:29
- 大小:28.66KB
船舶制造英语日常用语.docx
《船舶制造英语日常用语.docx》由会员分享,可在线阅读,更多相关《船舶制造英语日常用语.docx(29页珍藏版)》请在冰豆网上搜索。
船舶制造英语日常用语
船舶制造英语日常用语
好东西大家分享啊
船舶制造英语日常用语
一. 船体
1. Youmustweldandgrindthisareabeforepainting.
在油漆之前你必须把这个地方电焊修补、打磨好。
2. Thisweldinglineshouldbegougedandweldedagainbeforetightnessinspection.
这条焊缝在密性检查前要碳刨、再焊。
3. Thestructureofthestarboardsideisdifferentfromtheportside.
右舷的结构跟左舷的不一样。
4. Weshouldreinforcethedownsideofthewindlass.
我们应该在锚机的反面加强。
5. Thenavigationdeckisnotplain, wewillfairthedeckbyhotworking.
驾驶甲板不平,我们要火工校正。
6. Therearetwopiecesofstiffenersandbracketsmustbereplaced.
有两块加强筋和肘板要换新。
7. Twomorefootrestsandhandgripsshouldbeinstalledattheentranceofthesmallhatchcover.
在小舱口盖的进口处再安装两只踏步和拉手。
8. CheckingthejointaccuracyandstructureintegritybetweenNo.8andNo.9blockafterclosed.
No.8与No9分段合拢后大接头装配精确性和结构完整性检查。
9. Checkingstructureintegrityofsuperstructure(deckhouse)afterwelding.
上层建筑焊后结构完整性检查。
10. Inspectingfittingaccuracyofhatchcoamingonboard.
货舱口围板船上安装精度检查。
11. Inspectionairpressuretest(withwaterhead)forNo1.waterballasttank(No15block).
No1压载水舱(No.15分段)气压试验(压头试验)检查。
12. Inspectionhosingtestforupperdeck.
上甲板冲水试验检查。
13. Measuringhull’smaindimensions:
lengthoverall(LOA.),lengthbetweenperpendiculars(LPP.),breathmolded(B.),depthmolded(D.)anddeflectionbeforelaunching.
下水前测量船体主尺度:
总长、两柱间长、型宽、型深、基线挠度。
14. Inspectiondistancebetweendraughtmarksandkeelplateaftermarkingout.
划线后检查吃水标尺至平板龙骨之间的距离。
15. Inspectingfittingaccuracyofdraughtmark(loadinglinemark).
吃水标志(载重线标志)安装精确性检查。
16. Inspectionweldingseamanddimensionofcargohatchcover.
货舱舱口盖焊缝和尺度检查。
二. 轮机
1. Inspectionmachiningdimensionofpropellershaft(intermediateshaftorcountershaft).
螺旋桨轴(中间轴)机加工尺寸检查。
2. Checkforsurfacecontactarea(metalliccontact)betweensternshaftandpropellerhubtapers.检查螺旋桨轴与螺旋桨锥度接触面。
3. Inspectionmachiningdimensionofrudderstock.
舵杆机加工尺寸检查。
4. Inspectionruddercarrierafterassembly.
上舵承组装后检查。
5. Inspectionmachiningdimensionofrudderpintle.
舵销机加工尺寸检查。
6. Inspectionalignmentofstock,rudderbladeandpintle.
舵杆、舵叶、舵销连接后中心线检查。
7. Loweringtestandtensiontestofanchor.
锚投掷试验和拉力试验。
8. Measuringdimensionofshaftcouplingboltsandreamerhole.
轴系连接螺栓和钻孔尺寸测量。
9. Inspectioninstallationcorrectnessofship’snameplate(funnelmark).
船名牌(烟囱标志)安装正确性检查。
10. Flexibilityandhosingtestforsmallwatertighthatchcover(watertightdoorandwindow).
水密小舱口盖(水密门、窗)启闭灵活性、冲水检查。
11. Tightnesstest(openingandclosingtest,emergencyopeningandclosingtest)forcargohatchcover.
货舱舱口盖密性试验(启闭试验、应急启闭试验)。
12. Inspectinganchorthrowingawayappliance.
弃锚装置检查。
13. Inspectingcenterlinepositioningforshaftsystemandruddersystembeforeboring.
轴、舵系镗孔前中心线定位检查。
14. Opticalalignedcheckforshaftsystemafterboring.
轴系镗孔后光学校中检查。
15. HydraulictestforL.O.pipeforsterntube.
艉轴管滑油液压试验。
16. Measuringdiameterofforeandaftsterntubebearingandbushes.
艉轴管前、后轴承与衬套直径测量。
17. Inspectionpush-uploadforforeandaftsterntubebushes.
艉轴管前、后衬套压入检查。
18. Measuringclearancebetweenpropellershaft&bearing.
螺旋桨轴与轴承间隙测量。
19. FlushingL.O.systemofsterntube.
艉轴管滑油系统的投油清洗。
20. Inspectingzero(datum)positionofrudderblade.
舵叶0位检查。
21. Measuringclearanceofrudderjumpingstopper.
舵止跳块的间隙测量。
22. Inspectingintegrityofsteeringgear.
操舵装置完整性检查。
23. Measuringinstallationclearanceofrudderbearing.
舵轴承安装间隙测量。
24. Flushingofpipingsystemforsteeringgear.
舵机管路系统的投油清洗。
25. Mooringtestofsteeringgear.
舵机系泊试验。
26. Manoeuvingtestofsteeringgearduringseatrial.
舵机航行中操舵试验。
27. Emergencymanoeuvingtestofsteeringgear.
舵机应急操舵试验。
28. Installationandalignmentinspectionofwindlass.
锚机安装与校中检查。
29. Anchoringandweighingtestofwindlassonseatrial.
锚机航行中抛起锚试验。
30. Adjustingsafetydeviceforhydraulicsystemofsteeringgear(windlass、mooringwinch).
舵机(锚机、绞缆机)液压系统安全装置调整。
31. Runningtestandloadingtestfor4tprovisioncrane.
4吨食物吊运转试验和吊重试验。
32. Loweringandhoistingtestforlifeboat.
救生艇收放试验。
33. Loadingtestofaccommodationladder(pilotladder).
舷梯(引水员梯)压重试验。
34. Checkinglinerofmainengine(M.E.).
主机垫片检查。
35. Tighteninginspectionforthroughboltsofmainengine(M.E.).
主机贯穿螺栓紧固度检查。
36. Aligningmainengine’scrankshaftandintermediateshaftafterlaunching.
下水后主机曲轴和中间轴连接后校中。
37. Aligningintermediateshaftandpropellershaftafterlaunching.
下水后中间轴和螺旋桨连接后校中。
38. MeasuringdeflectionofcrankshaftofM.E.beforestartingup(afterseatrial).
主机动车前(航行试验后)
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 船舶 制造 英语 日常 用语