BOP系统试验大纲.docx
- 文档编号:27822183
- 上传时间:2023-07-05
- 格式:DOCX
- 页数:13
- 大小:21.76KB
BOP系统试验大纲.docx
《BOP系统试验大纲.docx》由会员分享,可在线阅读,更多相关《BOP系统试验大纲.docx(13页珍藏版)》请在冰豆网上搜索。
BOP系统试验大纲
伊拉克鲁迈拉项目
750修井机BOP系统联动试验大纲
甲方:
大庆油田公司井下作业分公司
乙方:
河北华北石油荣盛机械制造有限公司
防喷器组试验
一、试验目的
对大庆油田井下分公司所订购的防喷器组及配套设备进行功能试验。
另外,按照需方的要求进行其它项目的试验。
二、联动试验设备
防喷器组;钻井四通;防喷器控制装置;高压耐火软管;节流、压井管汇;
试验项目和要求
1、闸板防喷器液压开关动作操作,应无卡阻,到位准确;
2、闸板防喷器的四处密封试验;(闸板前部与管子的密封、闸板顶部与壳体的密封、侧门与壳体的密封、侧门腔与活塞杆间的密封)
3、FH28-35环形防喷器密封用31/2〞钻杆,进行35Mpa液压密封试验;
4、2FZ28-35双闸板防喷器上腔装31/2〞闸板总成,进行35Mpa液压密封试验;
5、2FZ28-35双闸板防喷器下腔装全封闸板;进行35Mpa液压密封试验;
三、试验前准备工作
1、联接F28-35防喷器组,安装顺序从上向下依次为:
FH35-35环形防喷器、2FZ35-35双闸板防喷器、FS35-35钻井四通和试压底座;
2、把防喷器组用地矛固定;
3、地面控置装置通过高压耐火软管与F28-35防喷器组相连接;
4、FS28-35钻井四通与手动阀门、液动阀门、内控管线、节流、压井管汇连接;
5、节流管汇低压区的法兰口用手动闸板阀安装好;
6、把地面控置装置油箱的液压油加到额定容量;同时把液压泵电机的电源、气动泵的气源连接好;
8、试压泵加满清水并把高压管线与试压底法兰进液口进行连接;
9、防喷器及节流、压井管汇内加满清水,
10、把地面控置装置的储能器压力升至21Mpa。
四、试验程序
(一)FH28-35环形防喷器试验
1、下入31/2"钻杆;
2、用液控压力10.5Mpa,关闭FH28-35环形防喷器,记录该压力值;
3、井压从0升至35Mpa,稳压15min,记录各段压力值、稳压时间;
4、密封情况:
目测油路、油缸无渗漏,密封部位无渗漏为合格。
5、泄井压为零;
6、打开FH28-35环形防喷器;
(二)2FZ28-35双闸板防喷器上腔半封闸板试验
1、下入-31/2"钻杆;
2、用液控压力10.5Mpa,关闭2FZ28-35双闸板防喷器上腔的31/2"闸板,记录该压力值;
3、打井压至1.4~2.1Mpa,稳压10min,压力降允许试验压力值的5%,升井压至
35Mpa,稳压10min,压力降允许试验压力值的5%,记录各段压力值、稳压时间;
4、密封情况:
目测各密封处无渗漏为合格;
5、泄井压为零;
6、打开2FZ28-35双闸板防喷器上腔31/2"闸板;
7、取出31/2"钻杆。
(三)2FZ28-35双闸板防喷器下腔全封闸板试验
1、用液控压力10.5Mpa,关闭2FZ28-35双闸板防喷器下腔全封闸板,记录该压力值;
2、打井压至1.4~2.1,稳压10min,压力降允许试验压力值的5%,升井压至35Mpa,稳压10min,压力降允许试验压力值的5%,记录各段压力值、稳压时间;
3、密封情况:
目测各密封处无渗漏为合格;
4、泄井压为零;
5、打开2FZ28-35双闸板防喷器下腔全封闸板;
五、试验完毕后
1、泄掉各部压力,排空防喷器内清水及控制回路的液压油,放空储能器的压力。
2、将环形防喷器、双闸板防喷器、钻井四通上面的水用空气吹扫干净,注意保护密封槽。
FKQ640-6G防喷器地面控制装置调试
一、试验目的
对大庆油田井下作业分公司所订购的防喷器地面控制装置及配套设备进行功能试验。
另外,按照需方的要求进行其它项目的试验。
二、联动试验设备
防喷器控制装置;防喷器组;钻井四通;高压耐火软管。
三、试验项目和要求
1、远程台三位四通液转阀开、中、关动作操作,应无卡阻,到位准确;
2、储能器组充压时间试验;
3、电动泵、气动泵自动启停试验;
4、溢流阀超压保护试验:
5、司钻台与远程台开关动作一致性试验;
6、关闭时间试验;
四、试验前准备工作
1、远程控制台储能器充气压力7±0.7MPa,气源压力0.65—0.8MPa,电源电压380±19V。
2、将远程控制台、司钻台、防喷器组、液压管线安装好。
五、调试程序
1、储能器组充压时间试验:
远程控制台泄压到7MPa,各三位四通液转阀处于“中位”的情况下,启动泵组给储能器组充压,记录从充压开始至压力升高到21MPa的时间,充压时间应小于15min。
2、电动泵、气动泵自动启停试验:
主令开关在“自动”位置,在油压降至接近19
MPa时自动接通电路,油压升至21
MPa时自动切断电路。
关闭气泵旁通阀,接气源0.53MPa~0.8MPa,使气泵在17.9
MPa时自动启动,油压升至21
MPa时自动停止,自动启停三次,启停可靠、运转正常。
3、溢流阀超压保护试验:
在主令开关放在手动位置、切断液气开关的情况下,启动泵组逐渐升压,观察益流阀开始产生溢流的压力,并且观察随着系统压力降低,导致溢流阀关闭的压力。
其调定压力不大于23.1MPa,其关闭压力不得低于18.9MPa。
4、司钻台与远程台开关动作一致性试验:
操作司钻控制台上各操作阀,观察远程控制台上相应的三位四通转阀的开关动作是否一致。
5、关闭时间试验:
在调压阀出口压力为10.5MPa条件下,操作司钻控制台上的各操作阀,记录关闭闸板防喷器、环形防喷器、液动阀的时间。
地面防喷器控制装置应能在30s内关闭任一个闸板防喷器。
标称通径小于476mm的环形防喷器,关闭时间不应超过30s。
标称通径等于或大于476mm的环形防喷器,关闭时间不应超过45s。
关闭或打开液动阀的时间,应小于防喷器组任一闸板防喷器的实际关闭时间。
节流管汇和压井管汇连调试验
一、试验目的
对YG35、JGY35压井、节流管汇进行联组,并进行功能试验。
二、试验项目和要求
YG35、JGY35压井、节流管汇试验液动节流阀动作操作,应无卡阻,到位准确;
1、节流管汇控制箱试验;
2、压井管汇和节流管汇的密封试验。
三、试验前的准备工作
1、按YG35、JGY35压井、节流管汇示意图,分别将压井、节流管汇安装到防喷器钻井四通两侧,将节流管汇外出口端用平行闸板阀关闭(没有阀的可用盲板法兰封死)。
2、节流、压井管汇内加满水。
四、试验程序
1、节流管汇出口端3只阀门关闭,其余阀门全部开启;压井管汇阀门关闭,井压至1.4-2.1Mpa,稳压10min,升压至35Mpa,稳压10min,记录各段压力值、稳压时间及密封情况。
2、节流管汇出口四通后1只阀门和节流阀前2只阀门关闭,其余阀门全部开启;压井管汇阀门关闭,井压至1.4-2.1Mpa,稳压10min,升压至35Mpa,稳压10min,记录各段压力值、稳压时间及密封情况。
3、节流管汇节流阀后2只阀门和五通出口前1只阀门关闭,其余阀门全部开启;压井管汇阀门关闭,井压至1.4-2.1Mpa,稳压10min,升压至35Mpa,稳压10min,记录各段压力值、稳压时间及密封情况。
4、节流管汇五通出口前三只阀门关闭,其余阀门全部开启;压井管汇单流阀前阀门开启,其余阀门全部关闭,井压至1.4-2.1Mpa,稳压10min,升压至35Mpa,稳压10min,记录各段压力值、稳压时间及密封情况。
5、钻井四通旁的液动平板阀与防喷器控制系统联动试验:
在液缸操作压力不超过10.5Mpa的情况下,保证阀门的正常开启与关闭。
全部试验结束。
Iraq鲁迈拉项目
BOPSystemJointTestProgramof750workoverrig
PartA:
DownholeOperationBranchofDaqingOilfield
PartB:
RongshengMachineryManufactureLtd.OfHuabeiOilfield,Hebei
BOPStackTest
一、Testpurpose
DocapacitytestforBOPstackandmatchingequipmentorderedbyDownholeOperationBranchofDaqingOilfiel.And,dootheritemstestaccordingtoPartA’srequirements.
二、Equipmentsfortest
BOPstack,drillingspool,BOPcontrolunit,high-pressurefirehoses;chokeandkillmanifold
Testitemanditsrequirements
1、ThehydraulicopenandcloseoperationoframBOPshouldbesmoothandaccurate.
2、FourpositionsealtestoframBOP(sealbetweenthefrontoframassemblyandpipe,sealbetweenthetopoframassemblyandthebody,sealbetweenthebonnetandthebody,sealbetweenthebonnetcavityandpistonrod)
3、Hydraulicsealtestof11”-5000psiAnnularBOPuses31/2”drillpipewithpressureof5000psi.
4、31/2”ramassemblyisinstalledintothetopcavityof11”-5000psiDoubleRamBOP.Dohydraulicsealtestwithpressureof5000psi.
5、Blindramassemblyisinstalledintothebottomcavityof11”-5000psiDoubleRamBOP.Dohydraulicsealtestwithpressureof5000psi.
三、Preparationbeforetest
1、Install11”-5000psiBOPstack.Theorder(fromtoptobottom)is11”-5000psiannularBOP,11”-5000psidoubleramBOP,11”-5000spoolandtestbase.
2、FixtheBOPstackwithspear.
3、ConnecttheBOPcontrolunitwith11”-5000psiBOPstackbyhigh-pressurefirehoses.
4、Connect11”-5000psispoolwithmanualvalve,hydraulicvalve,innercontrolpipe,chokeandkillmanifold.
5、Flangeofkillmanifoldshouldbeinstalledbymanualgatevalve.
6、AddhydraulicoilintheoilboxofBOPcontrolunittotheratedvolume.Connectthepowerofthehydraulicpumpmotor,gassourceoftheairpneumaticpump.
8、Fulfillwaterintothetestingpump.Connectthehighpressurepipewithinletoftestingbottomflange.
9、FulfillwaterintoBOP,chokeandkillmanifold.
10、IncreasepressureofBOPcontrolunitpressureaccumulatorto3000psi.
四、Testprocedure
Testof11”-5000psiAnnularBOP
1、Install31/2"drillpipe.
2、Close11”-5000psiannularBOPwith10.5MPahydraulicpressure.Andrecordthepressuredata.
3、Increasethewellpressurefrom0to5000psiandmaintainfor15min.Recordthepressureandtimeofeachperiod.
4、Sealcondition:
Observenoleakagefromoilpipeandoilcylinder.Thereisnoleakageonsealingparts.
5、Drainthewellpressureto0.
6、Open11”-5000psiannularBOP.
Halfsealpiperamassemblytestintopcavityof11”-5000psidoubleramBOP
1、Install31/2"drillpipe.
2、Close31/2”ramassemblyintopcavityof11”-5000psidoubleramBOPwith10.5MPahydraulicpressure.Andrecordthepressuredata.
3、Increasethewellpressureto200~300psiandmaintainfor10min.Pressuredropisallows5%oftestpressuredata.Increasethewellpressureto5000psiandmaintainfor10min.Pressuredropisallows5%oftestpressuredata.Recordthepressureandtimeofeachperiod.
4、Sealcondition:
Observenoleakageonsealpositions.
5、Drainthewellpressureto0.
6、Open31/2”ramassemblyinthetopcavityof11”-5000psidoubleramBOP.
7、Takeoff31/2"drillpipe.
(三)Blindramassemblytestintopcavityof11”-5000psidoubleramBOP
1、Closeblindramassemblyinbottomcavityof11”-5000psidoubleramBOPwith10.5MPahydraulicpressure.Andrecordthepressuredata.
2、Increasethewellpressureto200~300psiandmaintainfor10min.Pressuredropisallows5%oftestpressuredata.Increasethewellpressureto5000psiandmaintainfor10min.Pressuredropisallows5%oftestpressuredata.Recordthepressureandtimeofeachperiod.
3、Sealcondition:
Observenoleakageonsealpositions.
4、Drainthewellpressureto0.
5、Openblindramassemblyinthebottomcavityof11”-5000psidoubleramBOP.
五、Aftertest
1、Draineachpartpressure.DrainoffwaterintheBOPandhydraulicoilincontrolcircuit.Relieveallpressureoftheaccumulator.
2、CleanthewaterontheannularBOP,doubleramBOPandspoolbyair.Payattentiontoprotectthesealinggroove.
FKQ640-6GBOPcontrolsystemtest
四、Testpurpose
FunctiontestforBOPcontrolsystemandmatchingequipmentwhichmakefor大庆油田井下作业分公司.Alsocontainothertestaccordingtherequestofbuyer.
五、Testequipment
BOPControlsystem;BOPstacks;Drillingspool;High-pressurerefractoryhose
六、TestitemandRequirement
a)Theswitchof3-position4-wayvalveshouldbeflexibleandreliable;
b)TestofTimeforoilpressurerisingto21MPaforAccumulatorgroup;
c)StartandStopTestofOilPumpandAirPump;
d)OverpressureprotecttestofReliefvalve:
e)Testofcontrolsystem’son-offactionsamewithDrilling’spanel’soperation;
f)Closetimetest;
七、Preparejobfortest
a)Accumulatorchargepressureis7±0.7MPa,Airpressureis0.65—0.8MPa,voltageis380±19V。
b)FixBOPcontrolsystem,Drill’spanel,BOPstacksandhydraulicline
八、Programoftest
a)TestofTimeforoilpressurerisingto21MPaforAccumulatorgroup:
Pressurereliefofthesystem,makesurethatnitrogenpressureis7MPa±0.7MPa,closethereliefvalve,3-position4-wayvalveisat“middle”position,andmakeoilpressurerisingfrom7MPato21MPa.Startelectricpumpandairpump,timeforpressurerisingoftheaccumulatorsislessthan15minutes.
b)StartandStopTestofOilPumpandAirPump:
Whenthecommandswitchisatthe”automatic”position,adjustsystempressurecontrol,startsautomaticallywhenoilpressureis190+0.5MPaandstopsautomaticallywhenoilpressureisrisingto210-0.5MPa.Turnoffthebypass-valveofairpump,connectairsource(0.53-0.8)MPa.Theairpumpshallstartautomaticallypriortothepressuredecreasingbelow17.90+0.5MPaandshallstopautomaticallywhenoilpressureisrisingto210-1MPa,Stopsandstartsautomaticallythrice.
c)OverpressureprotecttestofReliefvalve:
Whenthecommandswitchisatthe”manual”positionandshutofftheairforHydro-pneumaticpressureswitch,startpumpunit,whenpressureraise,observethepressureofReliefvalveoverflow,andwhenpressuredecrease,observethepressureofReliefvalveshut.Theoverflowpressurenomorethan23.1MPa,andtheshutpressurenolessthan18.9MPa。
d)Testofcontrolsystem’son-offactionsamewithDrilling’spanel’soperation:
OperateallvalveofDrilling’spanel;observethecorresponding3-position4-wayvalveofBOPcontrolsystemwhetherornotsamewiththeoperation.
e)Closetimetest:
whentheAir/manualoperateregulatingvalve’soutportpressureat10.5MPa,operateallvalveofDrilli
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BOP 系统 试验 大纲