大型油罐水压试验方案Hydrostatic Testing Procedure for tank.docx
- 文档编号:24005516
- 上传时间:2023-05-23
- 格式:DOCX
- 页数:9
- 大小:18.76KB
大型油罐水压试验方案Hydrostatic Testing Procedure for tank.docx
《大型油罐水压试验方案Hydrostatic Testing Procedure for tank.docx》由会员分享,可在线阅读,更多相关《大型油罐水压试验方案Hydrostatic Testing Procedure for tank.docx(9页珍藏版)》请在冰豆网上搜索。
大型油罐水压试验方案HydrostaticTestingProcedurefortank
大型油罐水压试验方案
HydrostaticTestingProcedurefortank
1PURPOSE目的
Theprocedurespecifiedtheconditions,processandrequirementsofhydrostatictesting.
本程序规定了水压试验的条件、过程和要求。
2SCOPE范围
TheprocedureappliestohydrostatictestingactivityofbutadienetanksTXX2/XX3.
本程序适用于XX储罐TXX2/XX3的水压试验工作。
3REFERENCE编制依据
GBJ128-90Codeforconstructionandacceptanceofverticalcylindricalsteelweldedtanks
GBJ128-90立式圆筒形钢制焊接油罐施工及验收规范
XXStandardVerticalTanks–FieldErectionandTesting
XX标准直立罐-----现场安装和试验
API620DesignandConstructionofLarge,Welded,Low-PressureStorageTanks
API620大型焊接低压储罐设计和施工
4THECONDITIONSPROVIDEDWITHBEFOREHYDROSTATICTESTING水压试验进
行之前应具备下列条件
Thefollowingactionsshallbecompletedbeforefillingwithwater:
在充水之前,下列工作应该完成:
4.1罐底的所有焊缝应进行完真空箱试漏检查,并且检查合格;
Allweldedjointsinthebottomofthetankshallbeinspectedbymeansofavacuumbox,andaccepted.
4.2罐底与罐壁的角焊缝应进行真空箱试漏检查,并且检查合格;
Theshelltobottomjointsshallbeinspectedbymeansofavacuumbox,andaccepted.
4.3开孔的补强板应通入空气进行焊缝严密性检查,并且检查合格;
Theweldtightnessofthereinforcedplatearoundtheopeningshallbeinspectedbyapplyingair,and
accepted.
4.4沉降观测支座安装完毕;
Thepointsforsettlementmonitoringshallbefinished.
4.5所有的焊接工作都已经结束,并检查合格。
Allofweldingactivitieshavebeenfinished,andaccepted.
5HYDROSTATICTESTINGPROCEDURES水压试验程序
5.1General一般说明
5.1.1Storagetanksshouldbefilledinfourstages.应分四个阶段充水
Durationandintervalbetweenthevariousstagesshalldependonthesubsoilconditionsandthesettlement
monitoringduringhydrostatictesting.Accordingtothedesigneddocuments,thesubsoilconditions
underneathtankpadofTXX2/XX3arestiffclay.
不同阶段的持续时间和间隔时间应取决于地层土质和试验过程中的沉降观测计划。
根据设计文件,TXX2/XX3罐
基础的土质为硬粘泥土。
5.1.2Thesettlementduringandafterhydrostatictestingmustbemonitoredandrecorded.
试验过程中和试验后应进行沉降观测和记录。
5.1.3Watershallbefreshwater.
水应新鲜。
5.2BasicData基本数据
Fillingheight=21.6m
充水高度=21.6m
5.3Provisions有关规定
Theprovisionsdescribedin5.3.1through5.3.5shallbeappliedduringandafterwaterfillingforthe
hydrostatictest.
水压试验期间和水压试验之后,应满足5.3.1到5.3.5中描述的规定。
5.3.1Thetankshallbeventedtotheatmospherewhenitisfilledwithoremptiedofwater.
在充水和放水时,罐应和空气相通。
5.3.2Differentialsettlement,oruniformsettlementofsubstantialmagnitude,requiresanimmediatestopto
waterfilling.Anyfurtherfillingwithwaterwilldependonofthemeasuredsettlement.
沉降不均匀或均匀沉降量过大时,需要立即停止充水。
如果继续充水应依赖于测量的沉降值。
5.3.3Thetankshallbefilledwithwatertothedesignliquidlevel.
罐应充水到设计的液位。
5.3.4Afterthetankisfilledwithwaterandbeforepneumatictestpressureisapplied,anchorboltsshallbe
tightenedagainsttothehold-downbrackets.
在充水之后和充气之前,地脚螺栓应紧固在支座上。
5.3.4Allweldsintheshell,includingthecornerweldbetweentheshellandthebottom,shallbevisually
checkedfortightness.
所有罐壁上的焊缝,包括大角焊缝应检查严密性。
5.4TestingRate试验速率
Stage1阶段1
Fillingofthetankto10.0m,therateoffillingshould2metersperday.Thetotalfillingperdayshouldbe
completedinaperiodofnotlessthan3hours.Duringtheensuingbalanceofhoursintheday'stotalof24,the
foundationwillbeallowedtoequilibrate/consolidate/bemonitored.Aminimalequilibration/monitoringperiod
of6hoursareconsideredtobenecessary.
以每天2米的充水速度充水到10.0米。
每天总充水量宜在不少于3小时的期间内完成。
在接下来的时间里,对基
础应进行均衡/巩固/监测。
至少6小时的均衡/监测时间是很必要的。
Attheendofstage1,therewillbean36-hourequilibration/monitoringperiodbeforecommencementofstage
2.
在阶段1结束和阶段2开始之前,应有36个小时的均衡/监测时间。
Stage2阶段2
Fillingofthetankfrom10.0mto14.5m;therateoffillingshould1.25metersperday.Thetotalfillingtimeand
equilibration/monitoringperiodperdayshouldbeasforstage1above.Aminimalequilibration/monitoring
periodof8hoursisconsideredtobenecessary.
以每天1.25米的充水速度从10米充水到14.5米。
每天的总充水时间和均衡/监测时间见上述的阶段1。
至少8小时
的均衡/监测时间是很必要的。
Attheendofstage2,thereshouldbea36-hourequilibration/monitoringperiodbeforecommencementof
stage3.
在阶段2结束和阶段3开始之前,应有36小时的均衡/监测时间。
Stage3阶段3
Fillingofthetankfrom14.5mto18.0m;therateoffillingshould0.75metersperday.Thetotalfillingtimeand
equilibration/monitoringperiodperdayshouldbeasforstage1above.Aminimalequilibration/monitoring
periodof8hoursisconsideredtobenecessary.
以每天0.75米的充水速度从14.5米充水到18.0米。
每天的总充水时间和均衡/监测时间见上述的阶段1。
至少8小
时的均衡/监测时间是很有必要的。
Attheendofstage3,thereshouldbea48-hourequilibration/monitoringperiodbeforecommencementof
stage4.
在阶段3结束和阶段4开始之前,应有48小时的均衡/监测时间。
Stage4阶段4
Fillingofthetankfrom18.0mto21.6m;therateoffillingshould0.5metersperday.Thetotalfillingtimeand
equilibration/monitoringperiodperdayshouldbeasforstage1above.Aminimalequilibration/monitoring
periodof10hoursisconsideredtobenecessary.
以每天0.5米的充水速度从18.0米充水到21.6米。
每天的充水时间和均衡/监测时间见上述的阶段1。
至少10小时
的均衡/监测时间是很有必要的。
Attheendofstage4,thetankmustbeleftfullyfilledandmonitoredforatleast4moredays.
在阶段4结束时段,罐应充满水和至少4天的监测时间。
Stage5阶段5
所有的检查项目合格之后,开始放水。
5.5MeasurementOfTankBottomProfileBeforeHydrostaticTest水压试验前的基础表面检查
Thetankbottomprofileshallbemeasuredandrecordedbeforestartingtofillthetank.
在开始充水之前,应检查罐底表面,并做检查记录。
5.6MeasurementOfSettlementsDuringTesting试验过程中的基础沉降测量
Measurementofthetankfoundationsettlementsshouldbetakenfrom8pointsaccordingtothedrawings.
Inaccordancewiththefillingrateofatleast3hoursperday,thefollowingdailyscheduleof
measurementsshallbeapplied:
罐基础的沉降观测点应根据图纸设置。
根据每天3小时的充水速度,应进行下面的日常检查计划:
-priortothefillingperiod;充水之前
-justafterthefillingperiod;充水结束之际
-2hoursafterthefillingperiod(optional,dependingontheresults);
充水之后2小时(根据结果而定)
-5hoursafterthefillingperiod.充水之后5小时
Alsoduringeachequilibrationperiodbetweenthevariousstages,andduringtheperiodwhenthetankis
fullaftercompletionofstage4,andduringthedrainingofthetank,threemeasurementsshouldbetaken
daily.
在两个阶段之间的均衡时间和阶段4完成之后,以及在放水的过程中,宜进行日常测量。
5.7SettlementBehaviourDuringTesting试验过程中的沉降
Themeasureddailysettlementrateduringtheequilibrationandmonitoringperiodsbetweentwostates,
andduringtheperiodwhenthetankisfull(i.e.aftercompletionofstage4)shalldiminishwithtime(i.e.
thesettlementrateafterthesecondstageshallbelessthanthatafterthefirststage).
在两阶段之间的均衡和监测时间,充满水时(即阶段4完成之后),日常观测的沉降速度应随时间而减少(即:
阶段2之后的沉降速度应小于阶段1之后的沉降速度。
5.8EmptyingOfTheTankAfterTheHydrostaticTest水压试验后的放水
Waterdischargedshallbedrainouttodesignatedplacefarfromtankfoundationinordertoprotecttank
foundation.Beforethetestwaterispumpedordrainedfromthetank,adequatemeasuresshallbetaken
toavoidavacuumconditioninsidethetank.Forfixedrooftanks,allroofventsandmanholesshallbe
open.
为了保护基础,放出的水应被排放到指定的远离基础的地方。
在试验用水从罐里排放之前,应采取合适的措施
以避免罐内出现真空的情况。
对于固定顶,应打开所有的罐顶阀和人孔。
5.9MeasurementOfTankBottomProfileAfterTheHydrostaticTest水压试验后的罐底表面测量3
Afterthetest,about25cmofwatershouldbeleftinsidethetanktoensurethattankbottomisincontact
withitsfoundationprofile.
试验之后,罐内宜存留大约25cm高的水,保证罐底与基础的充分接触。
Thetankbottomprofileshallthenbemeasured.Themeasuredvaluesshallbeverifiedagainstthe
settlementpredictionsandrecordedinthetankmaintenancefile.
应进行罐底表面的测量。
测量值应根据沉降预测值进行核对,并记录在罐维护文件中。
6INLETANDDRAINOUTOFWATERPIPELINE进、出水管线图
RefertoAppendix.见附录A。
7THECALCULATIONTOCONFIRMTHEDIAMETEROFPIPE确定管径计算
7.1Thecalculationformulatorateofflow流量计算公式
Q=sv
thereinto:
其中:
Qisasrateofflow.Accordingcalculationofthetestingrateprogram,theaveragerateofflow:
0.010m3/s
Q为流量,m3/s。
根据充水速率计划计算,平均流量为:
0.010m3/s
visaslinearflowvelocity,m/s
v为线流速,m/s
7.2Formula柏努利公式
p=RELρv2/2d
Thereinto:
其中:
PisasthepipelinepressureappliedbyPMC,=7.5×103(N/m2)
P为PMC提供的用水管线的压力,=7.5×103(N/m2)
ReisasReynoldnumber
Re为雷诺系数,=0.8
Lisaslengthofpipeline
L为管线总长度,=50m
ρisasdensityofwater
ρ为水的密度,=1×103(kg/m3)
visasaveragelinearflowvelocity
v为平均线流速
disaspipediameter
d为管直径
7.3Thecalculationformulatopipediameter管直径计算
根据7.1和7.2,得:
Via7.1and7.2:
d=(8ReLPQ2/(Pπ2))1/5
=8×0.8×50×1×103×0.0102/(7.5×103×3.142)
=212mm
7.4Conclusion结论
ThepipediameterisDN200.
管线直径为DN200。
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 大型油罐水压试验方案Hydrostatic Testing Procedure for tank 大型 油罐 水压试验 方案 Hydrostatic
链接地址:https://www.bdocx.com/doc/24005516.html