cisco支持的命令.docx
- 文档编号:23492600
- 上传时间:2023-05-17
- 格式:DOCX
- 页数:23
- 大小:23.32KB
cisco支持的命令.docx
《cisco支持的命令.docx》由会员分享,可在线阅读,更多相关《cisco支持的命令.docx(23页珍藏版)》请在冰豆网上搜索。
cisco支持的命令
交换机支持的命令:
交换机基本状态:
switch:
;ROM状态,路由器是rommon>
hostname>;用户模式
hostname#;特权模式
hostname(config)#;全局配置模式
hostname(config-if)#;接口状态
交换机口令设置:
switch>enable;进入特权模式
switch#configterminal;进入全局配置模式
switch(config)#hostname;设置交换机的主机名
switch(config)#enablesecretxxx;设置特权加密口令
switch(config)#enablepasswordxxa;设置特权非密口令
switch(config)#lineconsole0;进入控制台口
switch(config-line)#linevty04;进入虚拟终端
switch(config-line)#login;允许登录
switch(config-line)#passwordxx;设置登录口令xx
switch#exit;返回命令
交换机VLAN设置:
switch#vlandatabase;进入VLAN设置
switch(vlan)#vlan2;建VLAN2
switch(vlan)#novlan2;删vlan2
switch(config)#intf0/1;进入端口1
switch(config-if)#switchportaccessvlan2;当前端口加入vlan2
switch(config-if)#switchportmodetrunk;设置为干线
switch(config-if)#switchporttrunkallowedvlan1,2;设置允许的vlan
switch(config-if)#switchporttrunkencapdot1q;设置vlan中继
switch(config)#vtpdomain;设置发vtp域名
switch(config)#vtppassword;设置发vtp密码
switch(config)#vtpmodeserver;设置发vtp模式
switch(config)#vtpmodeclient;设置发vtp模式
交换机设置IP地址:
switch(config)#interfacevlan1;进入vlan1
switch(config-if)#ipaddress;设置IP地址
switch(config)#ipdefault-gateway;设置默认网关
switch#dirflash:
;查看闪存
交换机显示命令:
switch#write;保存配置信息
switch#showvtp;查看vtp配置信息
switch#showrun;查看当前配置信息
switch#showvlan;查看vlan配置信息
switch#showinterface;查看端口信息
switch#showintf0/0;查看指定端口信息
2.路由器支持的命令:
路由器显示命令:
router#showrun;显示配置信息
router#showinterface;显示接口信息
router#showiproute;显示路由信息
router#showcdpnei;显示邻居信息
router#reload ;重新起动
路由器口令设置:
router>enable;进入特权模式
router#configterminal;进入全局配置模式
router(config)#hostname;设置交换机的主机名
router(config)#enablesecretxxx;设置特权加密口令
router(config)#enablepasswordxxb;设置特权非密口令
router(config)#lineconsole0;进入控制台口
router(config-line)#linevty04;进入虚拟终端
router(config-line)#login;要求口令验证
router(config-line)#passwordxx;设置登录口令xx
router(config)#(Ctrl+z);返回特权模式
router#exit;返回命令
路由器配置:
router(config)#ints0/0;进入Serail接口
router(config-if)#noshutdown;激活当前接口
router(config-if)#clockrate64000;设置同步时钟
router(config-if)#ipaddress;设置IP地址
router(config-if)#ipaddresssecond;设置第二个IP
router(config-if)#intf0/0.1;进入子接口
router(config-subif.1)#ipaddress;设置子接口IP
router(config-subif.1)#encapsulationdot1q;绑定vlan中继协议
router(config)#config-register0x2142;跳过配置文件
router(config)#config-register0x2102;正常使用配置文件
router#reload;重新引导
路由器文件操作:
router#copyrunning-configstartup-config;保存配置
router#copyrunning-configtftp;保存配置到tftp
router#copystartup-configtftp;开机配置存到tftp
router#copytftpflash:
;下传文件到flash
router#copytftpstartup-config;下载配置文件
ROM状态:
Ctrl+Break;进入ROM监控状态
rommon>confreg0x2142;跳过配置文件
rommon>confreg0x2102;恢复配置文件
rommon>reset ;重新引导
rommon>copyxmodem:
flash:
;从console传输文件
rommon>IP_ADDRESS=10.65.1.2;设置路由器IP
rommon>IP_SUBNET_MASK=255.255.0.0;设置路由器掩码
rommon>TFTP_SERVER=10.65.1.1;指定TFTP服务器IP
rommon>TFTP_FILE=c2600.bin;指定下载的文件
rommon>tftpdnld;从tftp下载
rommon>dirflash:
;查看闪存内容
rommon>boot;引导IOS
静态路由:
iproute;命令格式
router(config)#iproute2.0.0.0255.0.0.01.1.1.2;静态路由举例
router(config)#iproute0.0.0.00.0.0.01.1.1.2;默认路由举例
动态路由:
router(config)#iprouting;启动路由转发
router(config)#routerrip;启动RIP路由协议。
router(config-router)#network;设置发布路由
router(config-router)#negihbor;点对点帧中继用。
帧中继命令:
router(config)#frame-relayswitching;使能帧中继交换
router(config-s0)#encapsulationframe-relay;使能帧中继
router(config-s0)#fram-relaylmi-typecisco;设置管理类型
router(config-s0)#frame-relayintf-typeDCE;设置为DCE
router(config-s0)#frame-relaydlci16;
router(config-s0)#frame-relaylocal-dlci20;设置虚电路号
router(config-s0)#frame-relayinterface-dlci16;
router(config)#log-adjacency-changes;记录邻接变化
router(config)#ints0/0.1point-to-point;设置子接口点对点
router#showframepvc;显示永久虚电路
router#showframemap;显示映射
基本访问控制列表:
router(config)#access-listpermit|deny
router(config)#interface;default:
denyany
router(config-if)#ipaccess-groupin|out;default:
out
例1:
router(config)#access-list4permit10.8.1.1
router(config)#access-list4deny10.8.1.00.0.0.255
router(config)#access-list4permit10.8.0.00.0.255.255
router(config)#access-list4deny10.0.0.00.255.255.255
router(config)#access-list4permitany
router(config)#intf0/0
router(config-if)#ipaccess-group4in
扩展访问控制列表:
access-listpermit|denyicmp wild>[type] access-listpermit|denytcp wild>[port] 例3: router(config)#access-list101denyicmpany10.64.0.20.0.0.0echo router(config)#access-list101permitipanyany router(config)#ints0/0 router(config-if)#ipaccess-group101in 例3: router(config)#access-list102denytcpany10.65.0.20.0.0.0eq80 router(config)#access-list102permitipanyany router(config)#interfaces0/1 router(config-if)#ipaccess-group102out 删除访问控制例表: router(config)#noaccess-list102 router(config-if)#noipaccess-group101in 路由器的nat配置 Router(config-if)#ipnatinside;当前接口指定为内部接口 Router(config-if)#ipnatoutside;当前接口指定为外部接口 Router(config)#ipnatinsidesourcestatic[p]<私有IP><公网IP>[port] Router(config)#ipnatinsidesourcestatic10.65.1.260.1.1.1 Router(config)#ipnatinsidesourcestatictcp10.65.1.38060.1.1.180 Router(config)#ipnatpoolp160.1.1.160.1.1.20255.255.255.0 Router(config)#ipnatinsidesourcelist1poolp1 Router(config)#ipnatinsidedestinationlist2poolp2 Router(config)#ipnatinsidesourcelist2interfaces0/0overload Router(config)#ipnatpoolp210.65.1.210.65.1.4255.255.255.0typerotary Router#showipnattranslation rotary参数是轮流的意思,地址池中的IP轮流与NAT分配的地址匹配。 overload参数用于PAT将内部IP映射到一个公网IP不同的端口上。 外部网关协议配置: routerA(config)#routerbgp100 routerA(config-router)#network19.0.0.0 routerA(config-router)#neighbor8.1.1.2remote-as200 配置PPP验证: RouterA(config)#usernamepassword RouterA(config)#ints0 RouterA(config-if)#pppauthentication{chap|pap} 3.PIX防火墙命令 Pix525(config)#nameifethernet0outsidesecurity0;命名接口和级别 Pix525(config)#interfaceethernet0auto;设置接口方式 Pix525(config)#interfaceethernet1100full;设置接口方式 Pix525(config)#interfaceethernet1100fullshutdown Pix525(config)#ipaddressinside192.168.0.1255.255.255.0 Pix525(config)#ipaddressoutside133.0.0.1255.255.255.252 Pix525(config)#global(if_name)natidip-ip;定义公网IP区间 Pix525(config)#global(outside)17.0.0.1-7.0.0.15;例句 Pix525(config)#global(outside)1133.0.0.1;例句 Pix525(config)#noglobal(outside)1133.0.0.1;去掉设置 Pix525(config)#nat(if_name)nat_idlocal_ip[netmark] Pix525(config)#nat(inside)100 内网所有主机(0代表0.0.0.0)可以访问global1指定的外网。 Pix525(config)#nat(inside)1172.16.5.0255.255.0.0 内网172.16.5.0/16网段的主机可以访问global1指定的外网。 Pix525(config)#routeif_name00gateway_ip[metric];命令格式 Pix525(config)#routeoutside00133.0.0.11;例句 Pix525(config)#routeinside10.1.0.0255.255.0.010.8.0.11;例句 Pix525(config)#static(inside,outside)133.0.0.1192.168.0.8 表示内部ip地址192.168.0.8,访问外部时被翻译成133.0.0.1全局地址。 Pix525(config)#static(dmz,outside)133.0.0.1172.16.0.8 中间区域ip地址172.16.0.8,访问外部时被翻译成133.0.0.1全局地址。 ************************************************************************************************************************************************************************************** 1.在基于IOS的交换机上设置主机名/系统名: switch(config)#hostnamehostname 在基于CLI的交换机上设置主机名/系统名: switch(enable)setsystemnamename-string 2.在基于IOS的交换机上设置登录口令: switch(config)#enablepasswordlevel1password 在基于CLI的交换机上设置登录口令: switch(enable)setpassword switch(enable)setenalbepass 3.在基于IOS的交换机上设置远程访问: switch(config)#interfacevlan1 switch(config-if)#ipaddressip-addressnetmask switch(config-if)#ipdefault-gatewayip-address 在基于CLI的交换机上设置远程访问: switch(enable)setinterfacesc0ip-addressnetmaskbroadcast-address switch(enable)setinterfacesc0vlan switch(enable)setiproutedefaultgateway 4.在基于IOS的交换机上启用和浏览CDP信息: switch(config-if)#cdpenable switch(config-if)#nocdpenable 为了查看Cisco邻接设备的CDP通告信息: switch#showcdpinterface[typemodle/port] switch#showcdpneighbors[typemodule/port][detail] 在基于CLI的交换机上启用和浏览CDP信息: switch(enable)setcdp{enable|disable}module/port 为了查看Cisco邻接设备的CDP通告信息: switch(enable)showcdpneighbors[module/port][vlan|duplex|capabilities|detail] 5.基于IOS的交换机的端口描述: switch(config-if)#descriptiondescription-string 基于CLI的交换机的端口描述: switch(enable)setportnamemodule/numberdescription-string 6.在基于IOS的交换机上设置端口速度: switch(config-if)#speed{10|100|auto} 在基于CLI的交换机上设置端口速度: switch(enable)setportspeedmoudle/number{10|100|auto} switch(enable)setportspeedmoudle/number{4|16|auto} 7.在基于IOS的交换机上设置以太网的链路模式: switch(config-if)#duplex{auto|full|half} 在基于CLI的交换机上设置以太网的链路模式: switch(enable)setportduplexmodule/number{full|half} 8.在基于IOS的交换机上配置静态VLAN: switch#vlandatabase switch(vlan)#vlanvlan-numnamevla switch(vlan)#exit switch#configureteriminal switch(config)#interfaceinterfacemodule/number switch(config-if)#switchportmodeaccess switch(config-if)#switchportaccessvlanvlan-num switch(config-if)#end 在基于CLI的交换机上配置静态VLAN: switch(enable)setvlanvlan-num[namename] switch(enable)setvlanvlan-nummod-num/port-list 9.在基于IOS的交换机上配置VLAN中继线: switch(config)#interfaceinterfacemod/port switch(config-if)#switchportmodetrunk switch(config-if)#switchporttrunkencapsulation{isl|dotlq} switch(config-if)#switchporttrunkallowedvlanremovevlan-list switch(config-if)#switchporttrunkallowedvlanaddvlan-list 在基于CLI的交换机上配置VLAN中继线: switch(enable)settrunkmodule/port[on|off|desirable|auto|nonegotiate] Vlan-range[isl|dotlq|dotl0|lane|negotiate] 10.在基于IOS的交换机上配置VTP管理域: switch#vlandatabase switch(vlan)#vtpdomaindomain-name 在基于CLI的交换机上配置VTP管理域: switch(enable)setvtp[domaindomain-name] 11.在基于IOS的交换机上配置VTP模式: switch#vlandatabase switch(vlan)#vtpdomaindomain-name switch(vlan)#
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- cisco 支持 命令
![提示](https://static.bdocx.com/images/bang_tan.gif)