8实验八多层交换机静态路由实验Word格式文档下载.docx
- 文档编号:22015691
- 上传时间:2023-02-02
- 格式:DOCX
- 页数:11
- 大小:423.85KB
8实验八多层交换机静态路由实验Word格式文档下载.docx
《8实验八多层交换机静态路由实验Word格式文档下载.docx》由会员分享,可在线阅读,更多相关《8实验八多层交换机静态路由实验Word格式文档下载.docx(11页珍藏版)》请在冰豆网上搜索。
(2)交换机A和B通过的24口级联。
(3)配置交换机A和B各VLAN虚拟接口的IP地址分别如下表所示:
VLAN10
VLAN20
VLAN30
10.10.10.1
10.10.20.1
10.10.30.1
VLAN40
VLAN100
VLAN101
10.10.40.1
10.10.100.1
10.10.100.2
(4)主机1-主机4的网络设置为:
设备
IP地址
gateway
Mask
主机1
10.10.10.101
255.255.255.0
主机2
10.10.20.101
主机3
10.10.30.101
主机4
10.10.40.101
(6)验证:
①没有静态路由之前:
主机1与主机2,主机3与主机4可以互通。
主机1、主机2与主机3、主机4不通。
②配置静态路由之后:
四台主机之间都可以互通。
③若实验结果和理论相符,则本实验完成。
5、实验步骤
(1)交换机全部恢复出厂设置,配置交换机的VLAN信息
DCRS-5526S#conf
DCRS-5526S(Config)#vlan10
DCRS-5526S(Config-Vlan10)#switchportinterfaceethernet0/0/1-8
SettheportEthernet1/1accessvlan10sccessflly
SettheportEthernet1/2accessvlan10sccessflly
SettheportEthernet1/3accessvlan10sccessflly
SettheportEthernet1/4accessvlan10sccessflly
SettheportEthernet1/5accessvlan10sccessflly
SettheportEthernet1/6accessvlan10sccessflly
SettheportEthernet1/7accessvlan10sccessflly
SettheportEthernet1/8accessvlan10sccessflly
DCRS-5526S(Config-Vlan10)#exit
DCRS-5526S(Config)#vlan20
DCRS-5526S(Config-Vlan20)#switchportinterfaceethernet0/0/9-16
SettheportEthernet1/9accessvlan10sccessflly
SettheportEthernet1/10accessvlan10sccessflly
SettheportEthernet1/11accessvlan10sccessflly
SettheportEthernet1/12accessvlan10sccessflly
SettheportEthernet1/13accessvlan10sccessflly
SettheportEthernet1/14accessvlan10sccessflly
SettheportEthernet1/15accessvlan10sccessflly
SettheportEthernet1/16accessvlan10sccessflly
DCRS-5526S(Config-Vlan20)#exit
DCRS-5526S(Config)#vlan100
DCRS-5526S(Config-Vlan100)#switchportinterfaceethernet0/0/24
SettheportEthernet1/24accessvlan100sccessflly
DCRS-5526S(Config-Vlan100)#exit
DCRS-5526S(Config)#
验证配置:
DCRS-5526S#showvlan
图8-1交换机Avlan划分
DCRS-5526S#
DCRS-5526S(Config)#vlan30
DCRS-5526S(Config-Vlan30)#switchportinterfaceethernet0/0/1-8
SettheportEthernet0/0/1accessvlan30sccessflly
SettheportEthernet0/0/2accessvlan30sccessflly
SettheportEthernet0/0/3accessvlan30sccessflly
SettheportEthernet0/0/4accessvlan30sccessflly
SettheportEthernet0/0/5accessvlan30sccessflly
SettheportEthernet0/0/6accessvlan30sccessflly
SettheportEthernet0/0/7accessvlan30sccessflly
SettheportEthernet0/0/8accessvlan30sccessflly
DCRS-5526S(Config-Vlan30)exit
DCRS-5526S(Config)#vlan40
DCRS-5526S(Config-Vlan40)#switchportinterfaceethernet0/0/9-16
SettheportEthernet0/0/9accessvlan40sccessflly
SettheportEthernet0/0/10accessvlan40sccessflly
SettheportEthernet0/0/11accessvlan40sccessflly
SettheportEthernet0/0/12accessvlan40sccessflly
SettheportEthernet0/0/13accessvlan40sccessflly
SettheportEthernet0/0/14accessvlan40sccessflly
SettheportEthernet0/0/15accessvlan40sccessflly
SettheportEthernet0/0/16accessvlan40sccessflly
DCRS-5526S(Config-Vlan40)#exit
DCRS-5526S(Config)#vlan101
DCRS-5526S(Config-Vlan101)#switchportinterfaceethernet0/0/24
SettheportEthernet0/0/24accessvlan101sccessflly
DCRS-5526S(Config-Vlan101)exit
图8-2交换机Bvlan划分
(2)配置交换机各vlan虚拟接口的IP地址
DCRS-5526S(Config)#intvlan10
DCRS-5526S(Config-If-Vlan10)#ipaddress10.10.10.1255.255.255.0
DCRS-5526S(Config-If-Vlan10)#noshut
DCRS-5526S(Config-If-Vlan10)#exit
DCRS-5526S(Config)#intvlan20
DCRS-5526S(Config-If-Vlan20)#ipaddress10.10.20.1255.255.255.0
DCRS-5526S(Config-If-Vlan20)#noshut
DCRS-5526S(Config-If-Vlan20)#exit
DCRS-5526S(Config)#intvlan100
DCRS-5526S(Config-If-Vlan100)#ipaddress10.10.100.1255.255.255.0
DCRS-5526S(Config-If-Vlan100)#noshut
DCRS-5526S(Config-If-Vla100)#
DCRS-5526S(Config-If-Vla100)#exit
DCRS-5526S(Config)#intvlan30
DCRS-5526S(Config-If-Vlan30)#ipaddress10.10.30.1255.255.255.0
DCRS-5526S(Config-If-Vlan30)#noshut
DCRS-5526S(Config-If-Vlan30)#exit
DCRS-5526S(Config)#interfacevlan40
DCRS-5526S(Config-If-Vlan40)#ipaddress10.10.40.1255.255.255.0
DCRS-5526S(Config-If-Vlan40)#exit
DCRS-5526S(Config)#intvlan101
DCRS-5526S(Config-If-Vlan101)#ipaddress10.10.100.2255.255.255.0
DCRS-5526S(Config-If-Vlan101)#exit
(3)配置各主机的IP地址,注意配置网关
(4)验证主机之间是否连通
主机
端口
结果
原因
A:
1/1
1/9
通
Vlan100
1/24
Vlan101
B:
0/0/24
不通
主机3
B:
0/0/1
查看路由表,进一步分析上一步的现象原因。
交换机A:
DCRS-5526S#showiproute
图8-3查看交换机A路由信息
交换机B:
图8-4查看交换机B路由信息
DCRS-5526S#
(5)配置静态路由
DCRS-5526S(Config)#iproute10.10.30.0255.255.255.010.10.100.2
DCRS-5526S(Config)#iproute10.10.40.0255.255.255.010.10.100.2
验证配置
图8-5验证交换机A静态路由配置信息
DCRS-5526S(Config)#iproute10.10.10.0255.255.255.010.10.100.1
DCRS-5526S(Config)#iproute10.10.20.0255.255.255.010.10.100.1
图8-5验证交换机B静态路由配置信息
(6)验证主机之间是否连通
6、思考题
1、如果把交换机B上的vlan30改成vlan10,请问两台交换机上的vlan10是同一个么?
2、第四步中,主机1pingvlan101以及主机1ping主机3都不通,其原因各是什么?
7、相关配置命令详解
iproute
命令:
iproute<
ip_address>
<
mask>
<
gateway>
[<
preference>
]
noiproute<
功能:
配置静态路由:
本命令的no操作为删除静态路由。
参数:
和<
分别为目的IP地址和子网掩码,点分十进制格式;
为下一跳的IP地址,点分十进制格式;
为路由优先级,取值范围为1~255,preference的值越小优先级越高。
命令模式:
全局配置模式
showiproute
showiproute[dest<
destination>
][mask<
destMask>
][nextHop<
nextHopvalue>
][protocol{connected|static|rip|ospf|osps_ase|bgp|dvmrp}][vlan-id][preference<
pref>
][count]
显示路由表。
为目标网格地址;
为目标网格的掩码;
为下一跳IP地址;
connected为直连路由;
static为静态路由;
rip为RIP路由;
ospf为OSPF路由;
|osps_ase为OSPF引入的路由;
bgp为BGP路由;
dvmrp为DVMRP路由;
vlan-id>
为Vlan标识符;
为路由优先级,取值范围为0~255;
count为显示IP路由表项数信息。
特权用户配置模式
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 8实验八 多层交换机静态路由实验 实验 多层 交换机 静态 路由