华为MA配置成普通交换机的方法Word文档格式.docx
- 文档编号:21463378
- 上传时间:2023-01-30
- 格式:DOCX
- 页数:9
- 大小:105.61KB
华为MA配置成普通交换机的方法Word文档格式.docx
《华为MA配置成普通交换机的方法Word文档格式.docx》由会员分享,可在线阅读,更多相关《华为MA配置成普通交换机的方法Word文档格式.docx(9页珍藏版)》请在冰豆网上搜索。
save
以上配好就可以当交换机去用了。
附图:
如果出现的是1515,则需要再敲一遍该命令。
硬件连接方式
首先连接电脑与onu,通过配置线连接
图为配置线,“网线头”插入onu的CONSOL日,另一端与电脑的串口接。
图为onu上对应的CONSOL接口(插入“网线头”即可)
电脑端操作
首先打开超级终端:
开始一程序一附件---通信一超级终端
打开超级中断后出现如下提示
点否进入如下界面
名称随便写
图标选
择默认的即可,然后点击确定出现如下界面
连接口选择COM或者COM2艮据自己的机器选择,1不行就2,点击确定,
然后按照下图设置
[还原刀眾认说©
j]
[确走]「取洎]〔包用即
点击确定
然后到文件一属性一设置中按下图方式
定要设置
ASCII码
按照图中行延迟和字符延迟都设置为200毫秒,然后点击确定即
在超级终端出点击回车即可出现要求输入用户名和密码
华为onu登陆用户名root
密码mduadmin
登陆后界面如下
登陆onu后输入的命令:
enable---回车
eraseflashdata---回车
Y---回车
rebootsystem---回车
Y---回车
回车后等待片刻onu重启后以前所配置的数据即可全部删除
查看光功率
enable
MA5626#config
MA5626(config)#interfacegponnni0/0/1
MA5626(config-if-gponnni-0/0/1)#displayportstate
F/S/P
0/0/1
Laserstate
AUTO
Portstate
Up
WaveLength(nm)
1310
Identifier
Module/connectorsolderedto
motherboard
GBIC/SFPfunctionisdefinedbyserialIDonly
Connector
Opticalpigtail
Encoding
NRZ
BR,Nominal(100Mbps)13
Length(9um)(km)
Length(50um)
Notsupport
LengthNotsupport
Length(Copper)
Cc_base
0xaa
CC_EXT
0x7b
BR,max
Unspecified
BR,min
Invalid
Options
VendorRev
VendorPN
SFU3424THPCDFIAC
VendorSN
C4L2011876
VendorOUI
000000
Manufactured
12-03-21
Vendorname
SOURCEPHOTONICS
TXBiascurrent(mA)SupplyVoltage(V)Temperature(C)
TXpower(dBm)
RXpower(dBm)
8口实例
{<
cr>
|profile-name<
K>
}:
Command:
vlanservice-profileprofile-id1
MA5626(config-vlan-srvprof-1)#user-bridgingenable
Info:
Pleaseusethecommitcommandtomakemodificationstakeeffect
MA5626(config-vlan-srvprof-1)#commitMA5626(config-vlan-srvprof-1)#quit
MA5626(config)#vlanbindservice-profile1profile-id1MA5626(config)#multi-service-portvlan1port0/11-8user-vlanuntaggedrx-cttr6tx-cttr6
Itwilltakeseveralminutes,andconsolemaytimeout,pleaseusecommand
idle-timeouttosettimelimit
Areyousuretocreateservicevirtualport(s)?
(y/n)[n]:
y
Thenumberoftotalboardinthisoperation:
1
Thenumberoftotalservicevirtualportinthisoperation:
8
Creatingstart...
Creatingend:
Thenumberoftotalservicevirtualportwhichneedbecreated:
Thenumberoftotalservicevirtualportwhichhavebeencreated:
8
MA5626(config)#multi-service-portvlan1port0/11-8user-vlanuntaggedrx-cttr6tx-cttr6
0
MA5626(config)#save
POE功能
数字光模块版的光口查询光功率
MA5626(config-if-eth-0/0)#displayport?
CommandofethMode:
ddm-infoDisplayddminformationofopticalmoduleoptic-power-thresholdDisplayTXopticalpowerthresholdopticstateDisplayinformationofopticalmodulestateDisplayportstatestatisticsDisplayportstatisticstrafficDisplayporttrafficMA5626(config-if-eth-0/0)#displayportopticstate{all<
|portid<
U>
<
1,2>
displayportopticstate
A
%Incompletecommand,theerrorlocatesat'
A'
MA5626(config-if-eth-0/0)#displayportopticstate
allAllports
portid<
PortID
MA5626(config-if-eth-0/0)#displayportopticstateall
Portbit9umlength50umlengthlengthcopperlengthtyperatesupportedsupportedsupportedsupported(100M/s)(km)(10m)(10m)(m)
1
2211055M1000BASE_CX
1211055
M1000BASE_CX
2
550
MA5626(config-if-eth-0/0)#quit
MA5626(config)#displayboard0
0H822EPUBActive_normalUP2A
1H821EPFANormal
2
MA5626(config)#interfaceeth0/0
55
MA5626(config-if-eth-0/0)#displayportstateall
PortPortOpticMDISpeedDuplexFlow-ActiveLinkTypeStatus(Mbps)CtrlState
1GEnormal-auto_1000auto_fulloffactiveonline
active
2GEabsence-autoautooffoffline
Note:
Fora1000M,electricalportinthefull-duplexmode,settingMDItoanyvalueisinvalid
MA5626(config-if-eth-0/0)#displayportddm-infoall
%Parametererror,theerrorlocatesat'
MA5626(config-if-eth-0/0)#displayportddm-info
{portid<
displayportddm-info
MA5626(config-if-eth-0/0)#displayportddm-info1
Temperature(C):
Supplyvoltage(V):
TXbiascurrent(mA):
TXpower(dBm):
RXpower(dBm):
MA5626(config-if-eth-0/0)#displayportddm-info2
Failure:
Theopticmoduleofportisabsence,cannotdosuchoperation
MA5626(config-if-eth-0/0)#
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 华为 MA 配置 普通 交换机 方法
![提示](https://static.bdocx.com/images/bang_tan.gif)