弹簧补偿装置Word文档下载推荐.docx
- 文档编号:21361471
- 上传时间:2023-01-30
- 格式:DOCX
- 页数:9
- 大小:823.16KB
弹簧补偿装置Word文档下载推荐.docx
《弹簧补偿装置Word文档下载推荐.docx》由会员分享,可在线阅读,更多相关《弹簧补偿装置Word文档下载推荐.docx(9页珍藏版)》请在冰豆网上搜索。
TR450和TR750,TR450的张紧调节量为450mm,补偿张力为6-22.5KN;
TR750的张紧调节量为750mm,补偿张力为5-22.5KN.如果需要更高的拉力,可以并排使用两个弹簧补偿装置。
a.Whencabletensileis15KN,asetofTR750/1500CAT.790/197shallbeadopted,thelengthexpansionis750mm;
线张力为15KN,弹簧补偿装置选用TR750/1500CAT.790/197一套,张紧调节量750mm;
b.Whencabletensileis25KN,2setsofTR750/1275shallbeadopted,thelengthexpansionis750mm.
2线张力为25KN,弹簧补偿装置选用TR750/1275两套,张紧调节量750mm。
c.Whencabletensileis8.5KN,asetsofTR750/850shallbeadopted,thelengthexpansionis750mm.
线张力为8.5KN,弹簧补偿装置选用TR750/850一套,张紧调节量750mm
d.ThedetailedconfigurationsolutionandthetypeoftheproductwillbedefinedduringtheDesignLiaisonMeeting.
e.ThetechnicalinformationincludingthedetailedmaterialofthecomponentshallbeprovidedduringtheDesignLiaisonMeeting.
3ProductAcceptanceStandards产品验收标准
Thedrawingsandtestreportswillbeusedasreferencefortheproductacceptance.
图纸和检验报告作为产品验收参考.
3.1.OpenCaseInspection开箱验收
Inthedeliveriesitincludesthepackinglist,thedrawingsandtheinstallationmanuals.WhendoingtheOpenCaseInspection,pleasecarefullycheckthetype,dimensionandQTYaccordingtothepackinglist.
产品在发货时会随产品附有装箱单,图纸和安装手册.开箱验收请清点以上附件是否齐备,货物型号,规格和数量是否与装箱单上所填内容一致。
3.2.Appearance&
DimensionInspections外观及尺寸检验
3.2.1AppearanceInspection外观检验
Mainlycheckifthereisanyappearancedamageormechanical
damageduringthetransportation.
货物外观检验主要是检查货物在运输过程中有无外观及机械损伤;
3.2.2DimensionInspection尺寸检验
Dotheinspectionaccordingtothedimensionsspecifiedinthedrawings.
货物尺寸检验以零件图纸尺寸作为检验依据.
4.PerformanceInspection性能检验
Mechanical&
electricalperformanceshallbeinspectedbasedonthedatainthetestreportsprovidedbytheManufacturer,ortherelevantstandardsandmethodsmadebytheBuyer,orpickupsomesamplesatrandomandsendthemtotheBuyerinspectioncenterfortests.
零件的机械、电等性能检验以制造商提供的试验报告上检测的性能指标为依据,也可根据买方相关产品检验标准和方法,随机抽检样品送买方检测中心进行检测。
Seeattacheddrawing.图纸附后
铁路接触线自动张紧装置(专利产品)
工作原理Functionalprinciple
弹簧连接在线索上,弹簧驱动一个具有不变半径的滑轮。
该滑轮与另一个具有可变半径滑轮安装在同一个轴上。
线索与该轴相连接。
Thespringisconnectedtoacable,drivingapulleyhavingaconstantradium,assembledonthesameaxisofanotherpulleyhavingavariableradius,towhichthelineisconnected.
弹簧对滑轮系统有一个力矩。
这个力矩由紧固线索时产生的张力来补偿。
Thespringappliestothepulleysystematorquewhichiscompensatedbythetorquegeneratedbythelinepull.
弹簧预先加载了相当于弹簧行程总长一半的力,这不断变化的弹力在其行程以内,由连接在线索上的可变半径滑轮来补偿,在滑轮系统中这两个力矩是相等的。
线索张力在弹簧行程中保持不变。
Thespringispre-loadedatthehalfoftheforcecorrespondingtothetotaltravelofthespring.Thevariationofthespringforce,duringitstravel,iscompensatedbytheradiusvariationofthepulleyconnectedtotheline.The
twotorquesactingonthepulleysystemarethenconstantlyinequilibrium,andtheforceappliedtothelineremainspracticallyconstantduringallthespringtravel.
棘轮类型和选型
Springtensionningdevicetypesandtypeselection
专利产品棘轮可在昼夜、冬夏温度变化时自动对接触线或承力索的热胀冷缩变化进行补偿,保持张力恒定不变。
Springtensionningdeviceisatensioningdeviceformaintainingautomaticallyconstantthepullofrailwaycontactwiresorfeederwires,duringtheelongationorcontractionsofthesame,duetotemperaturevariations
betweendayandnight,summerandwinter.
棘轮直接串接于接触线终端,和传统滑轮补偿装置相比,由于减少了坠陀而不占用垂直和侧面空间。
另外,一种装置可满足不同长度的线索和不同的温度变化需求。
Contrarilytothetraditionalweight-tensioning,itdoesnotoccupyspaceverticallyorlaterally,asitisinstalledoverhead,inseriestothewire.Inaddition,onedeviceonlyissuitableforavarietyofspanlengthsandtemperaturevariations.
TR450和TR750,唯一区别是张紧能力大小。
(跨度和温度变化有关)
Basically,thereare2familiesofSpringtensionningdevice,TR450andTR750,differingonlyforthetensioningcapability(spanlengthrelatedtotemperaturevariation).
T450适用于温度变化较小,跨度较大或温度变化较大跨度较小的情况,可允许线长扩展值为450mm。
主要用于隧道和车站内。
T450issuitableforsmallertemperaturevariationsandlongspansorwidetemperaturevariationsandshorterspans,asitallowsamaximumlinelengthexpansionof450mm.Typicalapplicationsareintunnelsandstations.
T750适用于温度变化较大和跨度较大的情况,可允许线长扩展值为750mm。
T750issuitableforwidertemperaturevariationsandlongerspans,asitallowsamaximumlinelengthexpansionof750mm.
表1显示以上两种产品的适用范围Table1showstheapplicationrangeforbothfamilies.
客户在选型时需要考虑其使用接触网的实际拉力值和接触网及线类型以及棘轮产品适用的安装条件。
Thecustomerwillconsiderthepullvalueusedonhisnet,dependingonthewireandlinetype,andtheSpringensionningdevicefamilysuitablefortheinstallationconditions(spanlengthandtemperaturevariationintheregion).
以下是国际通用的一些标准线的拉力值Somestandardlinepullvaluesinternationallyusedare(Kg/daN):
750/736
1000/981
1380/1354
1500/1472
2000/1962
2250/2207
其他值可预测Othervaluecanbeforeseen.
表2是两种棘轮的安装尺寸Table2showsthemountingdimensionsforbothfamilies.
如果需要更高的拉力,可以并排使用两个棘轮。
例如,需求拉力为4000公斤时,可以用两组2000公斤的棘轮。
Forhigherpullvalues,2inparallelcanbeused.Forinstance,forapullof4.000Kg,22,000Kgcanbeused.
表3是并行棘轮的实例Table3showsanexampleofthisapplication.
表1Table1
10
客户提供资料
温度范围:
______℃
温差变化:
拉力:
__________㎏(daN)
选型:
棘轮:
TR_______
最大跨距:
______米
例如:
表2Table2
11
表3Table3
选择件3
标准件
选择件2
选择件1
12
A
-总线拉力等于两个单独棘轮的标准拉力的两倍
Thetotallinepullisequaltotwicethenominalpullofthesingle
Springtensionningdeviceisused.
-根据选型不同(TR450或TR750)张紧能力(扩展)保持450或750.
-
B
C
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 弹簧 补偿 装置