SOLID92Word格式文档下载.docx
- 文档编号:21137160
- 上传时间:2023-01-27
- 格式:DOCX
- 页数:16
- 大小:37.33KB
SOLID92Word格式文档下载.docx
《SOLID92Word格式文档下载.docx》由会员分享,可在线阅读,更多相关《SOLID92Word格式文档下载.docx(16页珍藏版)》请在冰豆网上搜索。
SOLID92输入摘要
结点:
I,J,K,L,M,N,O,P,Q,R
自由程度
UX,UY,UZ
实常数
无
物质属性
EX,EY,EZ,ALPX,ALPY,ALPZ,PRXY,PRYZ,PRXZ(或NUXY、NUYZ,NUXZ),DENS,GXY,GYZ,GXZ,DAMP
表面装载
压力:
面1(J-I-K),面2(I-J-L),面3(J-K-L),面4(K-I-L)
体装载
温度--
T(I),T(J),T(K),T(L),T(M),T(N),T(O),T(P),T(Q),T(R)
流力--
FL(I),FL(J),FL(K),FL(L),FL(M),FL(N),FL(O),FL(P),FL(Q),FL(R)
特殊性能
可塑性
蠕动
膨胀
应力硬化
大偏折
大张力
生死
自适应下降
初始应力输入
KEYOPT(5):
额外单元输出:
0--
基本的单元打印输出
1--
综合点打印输出
2--
节点应力打印输出
KEYOPT(6):
额外表面产品:
基本单元打印输出
4--
非零压力表面打印输出
KEYOPT(9):
初始应力子程序选项(只可通过KEYOPT命令直接输入):
没有用户子程序提供初始应力(缺省)
从用户子程序USTRESS读初始应力数据(参见《ANSYS用户编程序指南》)
SOLID92输出数据
单元求解数据以两种形式输出:
∙包括所有的节点解答数据的节点位移
∙另外的单元输出如表《"
SOLID92输出数据定义"
》
图SOLID92应力输出列出了几个栏目。
单元应力方向平行于单元坐标系。
表面应力输出是在表面坐标系中而且可应用于任一表面(KEYOPT(6))。
J-I-K坐标系如图"
SOLID92应力输出"
.其他表面坐标系如表面节点应力描述的相似方向。
只要在《单元解答》描述了的栏目表面应力打印输出才适用。
通用的解答输出描述见《单元解答》.
2.SOLID92应力输出
单元输出定义表使用如下标识记法:
冒号(:
)在命名专栏表明项目可由命令[ETABLE,ESOL]方法获取.在O栏表明项目输出到文件Jobname.OUT。
在R栏表明项目内容输出到结果文件。
在或O或R栏:
Y表明,栏目是可获取的,脚注数字表明项目是有条件地获取,和a-表明,项目是不可获取的。
表SOLID92单元输出定义
名字
定义
O
R
EL
单元数
Y
NODES
壁角结-I,J,K,L
MAT
材料序号
VOLU
体积
XC,YC,ZC
结果坐标
3
PRES
在结点J,I,K压力P1;
在I,J,L压力P2;
在J,K,L压力P3;
在K,I,L压力P4
TEMP
温度T(I),T(J),T(K),T(L)
FLUEN
流力FL(I),FL(J),FL(K),FL(L),FL(M),FL(N),FL(O),FL(P),FL(Q),FL(R)
S:
X,Y,Z,XY,YZ,XZ
应力
1,2,3
主应力
INT
应力强度
EQV
等效应力
EPEL:
弹性张力
主弹性张力
等效弹性张力[4]
-
EPTH:
热张力
1
等效热张力[4]
EPPL:
塑料张力
等效塑料张力[4]
EPCR:
蠕动张力
等效蠕动劳损[4]
EPSW:
膨胀张力
NL:
EPEQ
平均等效塑料张力
SRAT
在屈服表面应力与试验应力比
SEPL
应力曲线平均应力
HPRES
流体静压力
FACE
面标识
2
TRI
面节点
AREA
面区域
面平均温度
EPEL(X、Y,XY)
表弹性张力
表压力
S(X、Y,XY)
表应力
S(1,2,3)
表主要应力
SINT
表面应力强度
SEQV
表面等效应力
LOCI:
X,Y,Z
综合点位置
1.非线性解答(单元有非线性材料的输出)
2.表面输出(如果KEYOPT(6)=4并且有非零压力面)
3.只在矩心作为a*得到项目可利用。
4.等效张力使用有效的泊松比:
对有弹性和热力的这个值由用户设置(MP,prxy);
对塑性和蠕变这个值被设置在0.5.
SOLID92混合单元输出
描述
项目产品的名字
综合点应力解答
TEMP,SINT,SEQV,EPEL,S,EPPL,EPCR,EPSW,EPEQ,SRAT,SEPL,HPRES
结点应力
地点,TEMP,SINT,SEQV,S
1.如果KEYOPT(5)=1,出在每一合化点,
2.如果KEYOPT(5)=2,出在各个端点结。
表"
SOLID92项目和顺序编号"
名单输出了可通过ETABLE命令获取的栏目。
看见通用后处理器(POST1)在《ANSYS基本的分析指南》并且项目和顺序编号表在这个指南里对于更多信息。
以下记法被使用表"
:
名字
产品数量依照被定义在表"
SOLID92单元输出定义"
项目
被预先决定的项目标签为ETABLE命令
I,J,。
..,R
顺序编号为数据在结I,J,。
..,R
表.SOLID92项目和顺序编号
产品数量名字
ETABLE并且ESOL命令输入
项目
I
J
K
L
M,。
P1
SMISC
P2
4
5
6
P3
7
8
9
P4
11
10
12
NMISC
16
17
13
18
内部
14
19
15
20
看见表面解答在这个指南里为项目和顺序编号为表面产品为ETABLE命令。
SOLID92假设和制约
∙单元不能有零体积。
单元在图:
"
SOLID92几何模型"
或在I-J-K面板下中被编号。
∙有一个被去除中点的边缘表示,位移沿那个边缘线性地变化,而不是抛物线地变化。
见二次方单元(中间节点)在ANSYS塑造的和捕捉的指南对于关于对中节点的用途的信息。
SOLID92产品制约
ANSYS专家。
∙潮湿的物质不被允许。
∙流体载荷不适用。
唯一的特殊性是可以定义应力硬化。
原文:
3-D10-NodeTetrahedralStructuralSolid
SOLID92ElementDescription
SOLID92hasaquadraticdisplacementbehaviorandiswellsuitedtomodelirregularmeshes(suchasproducedfromvariousCAD/CAMsystems).SeeSOLID95fora20-nodebrickshapedelement.
Theelementisdefinedbytennodeshavingthreedegreesoffreedomateachnode:
translationsinthenodalx,y,andzdirections.Theelementalsohasplasticity,creep,swelling,stressstiffening,largedeflection,andlargestraincapabilities.SeeSOLID92intheANSYS,Inc.
TheoryReferenceformoredetailsaboutthiselement.
Figure92.1.SOLID92Geometry
SOLID92InputData
Thegeometry,nodelocations,andthecoordinatesystemforthiselementareshowninFigure92.1:
SOLID92Geometry"
.
Besidethenodes,theelementinputdataincludestheorthotropicmaterialproperties.Orthotropicmaterialdirectionscorrespondtotheelementcoordinatedirections.TheelementcoordinatesystemorientationisasdescribedinCoordinateSystems.
ElementloadsaredescribedinNodeandElementLoads.PressuresmaybeinputassurfaceloadsontheelementfacesasshownbythecirclednumbersonFigure92.1:
.Positivepressuresactintotheelement.Temperaturesandfluencesmaybeinputaselementbodyloadsatthenodes.ThenodeItemperatureT(I)defaultstoTUNIF.Ifallothertemperaturesareunspecified,theydefaulttoT(I).Ifallcornernodetemperaturesarespecified,eachmidsidenodetemperaturedefaultstotheaveragetemperatureofitsadjacentcornernodes.Foranyotherinputtemperaturepattern,unspecifiedtemperaturesdefaulttoTUNIF.SimilardefaultsoccursforfluenceexceptthatzeroisusedinsteadofTUNIF.
YoucanapplyaninitialstressstatetothiselementthroughtheISTRESSorISFILEcommand.Formoreinformation,seeInitialStressLoadingintheANSYSBasicAnalysisGuide.Alternately,youcansetKEYOPT(9)=1toreadinitialstressesfromtheusersubroutineUSTRESS.Fordetailsonusersubroutines,seetheANSYSGuidetoUserProgrammableFeatures.
YoucanincludetheeffectsofpressureloadstiffnessinageometricnonlinearanalysisusingSOLCONTROL,,,INCP.Pressureloadstiffnesseffectsareincludedinlineareigenvaluebucklingautomatically.Ifanunsymmetricmatrixisneededforpressureloadstiffnesseffects,useNROPT,UNSYM.
Asummaryoftheelementinputisgivenin"
SOLID92InputSummary"
.AgeneraldescriptionofelementinputisgiveninElementInput.
SOLID92InputSummary
Nodes
DegreesofFreedom
RealConstants
None
MaterialProperties
EX,EY,EZ,ALPX,ALPY,ALPZ,PRXY,PRYZ,PRXZ(orNUXY,NUYZ,NUXZ),DENS,GXY,GYZ,GXZ,DAMP
SurfaceLoads
Pressures
--
face1(J-I-K),face2(I-J-L),face3(J-K-L),face4(K-I-L)
BodyLoads
Temperatures
Fluences
FL(I),FL(J),FL(K),FL(L),FL(M),FL(N),FL(O),FL(P),FL(Q),FL(R)
SpecialFeatures
Plasticity
Creep
Swelling
Stressstiffening
Largedeflection
Largestrain
Birthanddeath
Adaptivedescent
Initialstressimport
KEYOPT(5)
Extraelementoutput:
0
Basicelementprintout
1
Integrationpointprintout
2
Nodalstressprintout
KEYOPT(6)
Extrasurfaceoutput:
4
Surfaceprintoutforfaceswithnonzeropressure
KEYOPT(9)
Initialstresssubroutineoption(availableonlythroughdirectinputoftheKEYOPTcommand):
Nousersubroutinetoprovideinitialstress(default)
ReadinitialstressdatafromusersubroutineUSTRESS(seetheANSYSGuidetoUserProgrammableFeaturesforuserwrittensubroutines)
SOLID92OutputData
Thesolutionoutputassociatedwiththeelementisintwoforms:
∙Nodaldisplacementsincludedintheoverallnodalsolution
∙AdditionalelementoutputasshowninTable92.1:
SOLID92ElementOutputDefinitions"
SeveralitemsareillustratedinFigure92.2:
SOLID92StressOutput"
.Theelementstressdirectionsareparalleltotheelementcoordinatesystem.Thesurfacestressoutputsareinthesurfacecoordinatesystemandareavailableforanyface(KEYOPT(6)).ThecoordinatesystemforfaceJ-I-KisshowninFigure92.2:
.Theothersurfacecoordinatesystemsfollowsimilarorientationsasindicatedbythepressurefacenodedescription.SurfacestressprintoutisvalidonlyiftheconditionsdescribedinElementSolutionaremet.AgeneraldescriptionofsolutionoutputisgiveninSolutionOutput.SeetheANSYSBasicAnalysisGuideforwaystoviewresults.
Figure92.2.SOLID92StressOutput
TheElementOutputDefinitionstableusesthefollowingnotation:
Acolon(:
)intheNamecolumnindicatestheitemcanbeaccessedbytheComponentNamemethod[ETABLE,ESOL].TheOcolumnindicatestheavailabilityoftheitemsinthefileJobname.OUT.TheRcolumnindicatestheavailabilityoftheitemsintheresultsfile.
IneithertheOorRcolumns,Yindicatesthattheitemisalwaysavailable,anumberreferstoatablefootnotethatdescribeswhentheitemisconditionallyavailable,anda-indicatesthattheitemisnotavailable.
Table92.1.SOLID92ElementOutputDefinitions
Name
Definition
ElementNumber
Cornernodes-I,J,K,L
Materialnumber
VOLU:
Volume
Locationwhereresultsarereported
PressuresP1atnodesJ,I,K;
P2atI,J,L;
P3atJ,K,L;
P4atK,I,L
TemperaturesT(I)
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SOLID92
![提示](https://static.bdocx.com/images/bang_tan.gif)