网络工程实验基于华为路由器交换机Word文档格式.docx
- 文档编号:19116947
- 上传时间:2023-01-03
- 格式:DOCX
- 页数:19
- 大小:597.76KB
网络工程实验基于华为路由器交换机Word文档格式.docx
《网络工程实验基于华为路由器交换机Word文档格式.docx》由会员分享,可在线阅读,更多相关《网络工程实验基于华为路由器交换机Word文档格式.docx(19页珍藏版)》请在冰豆网上搜索。
[switch-Ethernet0/3]quit
[switch]discurr
[switch]interfacevlan1
[switch-Vlan-interface1]ipaddress10.65.1.8255.255.0.0
[switch-Vlan-interface1]quit
[switch]iproute-static0.0.0.00.0.0.010.65.1.2
[switch]ipdefault-gateway10.65.1.2
[switch]save
(4)配置主机地址
login:
root
linux
[rootPCAroot]#ifconfigeth010.65.1.1netmask255.255.0.0
[rootPCAroot]#ifconfig
[rootPCAroot]#routeadddefaultgw10.65.1.2
[rootPCAroot]#route
(5)主机与交换机间的连通测试
[rootPCAroot]#ping10.65.1.8
[rootPCAroot]#telnet10.65.1.8
4.思考总结
(1)特权密码的作用是什么?
密码丢失如何处理?
(2)主机地址与交换机IP地址设置应注意哪些问题。
、
实验2端口聚合配置
(1)熟悉端口聚合命令的使用场合与注意事项
(2)掌握端口聚合配置的基本方法
(3)了解端口的属性类型
3.实验容步骤
(1)打开实验软件调用两台交换机并按实验拓扑连接
(2)配置交换机A的端口参数
端口E0/1
[Quidway]sysnameSwitchA
[SwitchA]interfaceethernet0/1
[SwitchA-Ethernet0/1]duplexfull
[SwitchA-Ethernet0/1]speed100
[SwitchA-Ethernet0/1]portlink-typetrunk
[SwitchA-Ethernet0/1]porttrunkpermitvlanall
端口E0/2
[SwitchA-Ethernet0/1]inte0/2
[SwitchA-Ethernet0/2]duplexfull
[SwitchA-Ethernet0/2]speed100
[SwitchA-Ethernet0/2]portlink-typetrunk
[SwitchA-Ethernet0/2]porttrunkpermitvlanall
(3)配置交换机B的端口参数
[Quidway]sysnameSwitchB
[SwitchB]interfaceethernet0/1
[SwitchB-Ethernet0/1]duplexfull
[SwitchB-Ethernet0/1]speed100
[SwitchB-Ethernet0/1]portlink-typetrunk
[SwitchB-Ethernet0/1]porttrunkpermitvlanall
[SwitchB-Ethernet0/1]inte0/2
[SwitchB-Ethernet0/2]duplexfull
[SwitchB-Ethernet0/2]speed100
[SwitchB-Ethernet0/2]portlink-typetrunk
[SwitchB-Ethernet0/2]porttrunkpermitvlanall
(4)配置端口聚合
[SwitchA]link-aggregationethernet0/1toethernet0/2both
[SwitchB]link-aggregationethernet0/1toethernet0/2both
[SwitchA]displaylink-aggregationethernet0/1
[SwitchA]undolink-aggregationall
(1)TRUNK端口可否属于多个VLAN?
(2)如何测试TRUNK端口的工作状态?
实验3VLAN的配置
(1)掌握VLAN命令使用的基本原则
(2)掌握VLAN划分的规则
(3)熟悉VLAN地址的分配方法
(4)学会如何测试VLAN间的连通性
3.实验容与步聚
(1)调用主机和交换机并按拓扑结构连
(2)配置交换机A的VLAN
[SwitchA]vlan2
[SwitchA-vlan2]porte0/2
[SwitchA-vlan2]porte0/3toe0/4
[SwitchA-vlan2]vlan3
[SwitchA-vlan3]porte0/5toe0/6
[SwitchA]disvlanall
[SwitchA]discurrent
(3)配置交换机B的VLAN
[SwitchB]vlan2
[SwitchB-vlan2]porte0/3toe0/4
[SwitchB-vlan2]vlan3
[SwitchB-vlan3]porte0/5toe0/6
[SwitchB-vlan3]quit
[SwitchB]disvlanall
[SwitchB]discurrent
(4)配置主机的IP
设置计算机的IP为:
PCA:
10.65.1.1PCB:
10.66.1.1PCC:
10.65.1.3PCD:
10.66.1.3
(5)测试VLAN的连通性
[rootPCAroot]#ping10.65.1.1通(本机IP)
[rootPCAroot]#ping10.65.1.3不通(中间连接线是vlan1)
[rootPCAroot]#ping10.66.1.1不通(不同网络,不同vlan)
[rootPCAroot]#ping10.66.1.3不通(不同网络,不同vlan)
[rootPCBroot]#ping10.66.1.3不通(中间连接线是vlan1)
4.思考与总结
(1)不同交换机的端口是不可在同一VLAN上?
(2)不同VLAN间主机是否可以通信?
(3)不同交换机上相同ID的VLAN可否通信?
实验4VLAN的高级配置
(1)学习主VLAN与附VLAN的配置方法
(2)了解主VLAN与子VLAN的关系
(3)了解子VLAN间的连通关系
(4)学会用VLAN技术管理网络
[SwitchA-vlan2]portethernet0/5toethernet0/6
[SwitchA]vlan3
[SwitchA-vlan3]portethernet0/7toethernet0/8
[SwitchA]vlan5
[SwitchA-vlan5]portethernet0/1toethernet0/4
[SwitchA-vlan5]isolate-user-vlanenable;
vlan5是主vlan
[SwitchA-vlan5]quit
[SwitchA]isolate-user-vlan5secondary2,3;
vlan2,3是子vlan
[SwitchB-vlan2]portethernet0/5toethernet0/6
[SwitchB]vlan3
[SwitchB-vlan3]portethernet0/7toethernet0/8
[SwitchA]vlan4
[SwitchB-vlan4]portethernet0/1toethernet0/4
[SwitchB-vlan4]isolate-user-vlanenable;
vlan4是主vlan
[SwitchB-vlan4]quit
[SwitchB]isolate-user-vlan4secondary2,3;
(4)按拓扑结构配置主机地址
A:
10.65.1.1
B:
10.65.1.2
C:
10.65.1.3
D:
10.65.1.4
(5)测试主VLAN与子VLAN的连通性
(6)测试子VLAN间的边通性
4.思考与总结
(1)分析主与附VLAN的连通性
(2)分析子VLAN间的连能性
(3)附VLAN设置的必要性分析
实验5交换机STP的配置
(1)了解STP配置的目的和用途
(2)了解STP解决广播风暴的基本原理
(3)学会STP配置方法
(2)启动各交换机的STP协议及优先级
[Quidway]stp{enable|disable}
[Quidway]stppriority4096设置交换机的优先级
[Quidway]stprootprimary设置交换机为树根
[Quidway-Ethernet0/1]stpcost200设置交换机端口的花费
(3)查看STP的运行情况
[Quidway]displaystp
(4)查看端口STP状态运行信息
[Quidway]displaystpinterfaceEthernet0/7
(1)分析STP抑制广播风暴的基本原理
(2)分析STP应用的环境要求
实验6直连路由测试
(1)掌握访问路由器的基本方法
(2)掌握主机与路由连通的测试
(3)网关的配置与连通性测试
(1)调用路由器及主机,按拓扑结构要求连接设备
(2)配置路由器口令及端口IP
<
Quidwqy>
[Quidway]interfaceethernet0/0
[Quidway-Ethernet0/0]ipaddr10.65.1.2255.255.255.0
[Quidway-Ethernet0/0]undoshutdown
[Quidway-Ethernet0/0]inte0/1
[Quidway-Ethernet0/1]ipaddr10.66.1.2255.255.255.0
[Quidway-Ethernet0/1]undoshutdown激活端口
(3)配置主机IP地址
[rootPCBroot]#ifconfigeth010.66.1.1netmask255.255.0.0
(4)主机与路由器的连通性测试
[rootPCAroot]#ping10.65.1.2(通,没网关只能ping直连的口)
[rootPCAroot]#ping10.66.1.2(不通,PCA没有设置网关)
(5)网关的配置与连通性测试
[rootPCAroot]#ping10.66.1.2(通)
[rootPCAroot]#ping10.66.1.1(不通,因PCB没有网关)
[rootPCBroot]#routeadddefaultgw10.66.1.2
[rootPCAroot]#ping10.66.1.1(通)
(6)主机与路由端口连通性测试
去掉计算机HostB与Router的连线,再ping:
[rootPCAroot]#ping10.66.1.2不通(没有接线端口会自动down掉)
再连接HostB与Router的连线,再ping:
(1)分析网关地址与网络连通的关系
(2)通过实验结果分析路由端口配置的技术要求
实验7单臂路由测试
(1)学习交换机与路由器通信的基本原理
(2)学习子接口的应用
(3)学习子接口与VLAN配置的对应关系
(4)学习主机与路由的连通性测试
(1)调用路由器、交换机和主机,按拓扑结构要求连接设备
(2)配置主机IP和网关
设置PCAip:
10.65.1.1gateway:
10.65.1.2
设置PCBip:
10.66.1.1gateway:
10.66.1.2
(3)配置子接口两个IP的情况
[Quidway-Ethernet0/0]ipaddr10.66.1.2255.255.255.0secondary
[rootPCAroot]#ping10.66.1.1
(4)划分两个子接口与两个vlan的路由应关系
[SwitchA-vlan2]porte0/3
[SwitchA-vlan3]porte0/6
[SwitchA]inee0/1
[SwitchA-Ethernet0/1]porttrunkencapdot1q
[SwitchA]discurr
[Quidway]inte0/0
[SwitchA-Ethernet0/0]inte0/0.1
[SwitchA-Ethernet0/0.1]encapsulationdot1q2
[SwitchA-Ethernet0/0.1]ipaddr10.65.1.2255.255.255.0
[SwitchA-Ethernet0/0.1]nudoshut
[SwitchA-Ethernet0/0.1]inte0.2
[SwitchA-Ethernet0/0.2]encapsulationdot1q2
[SwitchA-Ethernet0/0.2]ipaddr10.66.1.2255.255.255.0
[SwitchA-Ethernet0/0.2]nudoshut
(5)连通性测试
[rootPCAroot]#ping10.66.1.1通
(1)分析子接口的作用
(2)总结子接口配置的关键技术指标
实验8静态路由实验
(1)了解静态路由配置的环境要求
(2)掌握静态路由的配置方法
(3)学会查看路由表,分析路由参数
(1)调用设备并按拓扑要求连接设备
(2)配置主机地址
10.65.1.1netmask255.255.0.0
PCB:
10.71.1.1netmask255.255.0.0
PCC:
10.66.1.1netmask255.255.0.0
(3)配置路由器A端口
[RouterA]interfaceethernet0/0
[RouterA-Ethernet0/0]ipaddrress10.65.1.2255.255.0.0
[RouterA-Ethernet0/0]undoshutdown
[RouterA-Ethernet0/0]inte0/1
[RouterA-Ethernet0/1]ipaddrress10.66.1.2255.255.0.0
[RouterA-Ethernet0/1]undoshutdown
[RouterA-Ethernet0/1]ints0/1
[RouterA-Serial0/1]ipaddrress10.68.1.2255.255.0.0
[RouterA-Serial0/1]undoshutdown
[RouterA-Serial0/1]clockrate64000
[RouterA-Serial0/1]quit
[RouterA]iprouting
[RouterA]discurr
(4)配置路由器B端口
[RouterB]interfaceethernet0/0
[RouterB-Ethernet0/0]ipaddrress10.70.1.2255.255.0.0
[RouterB-Ethernet0/0]undoshutdown
[RouterB-Ethernet0/0]inte0/1
[RouterB-Ethernet0/1]ipaddrress10.71.1.2255.255.0.0
[RouterB-Ethernet0/1]undoshutdown
[RouterB-Ethernet0/1]ints0/0
[RouterB-Serial0/0]ipaddrress10.68.1.1255.255.0.0
[RouterB-Serial0/0]undoshutdown
[RouterB-Serial0/0]quit
[RouterB]iprouting
[RouterB]discurr
(5)配置主机A的网关及以太网端口IP
(6)测试主机A与路由器的连能性
[rootPCAroot]#ping10.65.1.2通
[rootPCAroot]#ping10.66.1.2通
[rootPCAroot]#ping10.67.1.2通
[rootPCAroot]#ping10.68.1.2不通
[rootPCAroot]#ping10.69.1.2不通
[RouterA]iproute-static10.69.0.0255.255.0.010.67.1.1
[rootPCAroot]#ping10.69.1.1通
(7)配置路由器的静态路由
设置RouterA的IP:
f0/0:
10.65.1.2--->
10.65.1.1
f0/1:
10.66.1.2--->
10.66.1.1
s0/0:
10.67.1.2
s0/1:
10.68.1.2--->
接RouterCs0/0
设置RouterB的IP:
10.78.1.1<
---
10.67.1.1
10.69.1.2--->
10.69.1.1
10.70.1.2--->
PCD:
10.70.1.1
(8)设置从PCA到PCC的静态路由
[ROA]iprouting
[ROA]iproute-static10.69.0.0255.255.0.010.68.1.1
[ROA]displayiproute
[ROB]iproute-static10.69.0.0255.255.0.010.78.1.1
[ROB]displayiproute
(9)连通性测试
[rootPCAroot]#ping10.69.1.1(通)
[rootPCAroot]#ping10.78.1.1(不通)
[rootPCAroot]#ping10.70.1.1(不通)
(1)分析实验结果,为什么PCA到10.78.1.1不通?
(2)查看路由表分析路由表各项参数
实验9动态路由实验
(1)了解动态路由协议的使用环境
(2)学会动态路由的配置方法
(3)学会子网连通性的测试
(4)动态路由与静态路由的应用对比
3.实验步骤与容
(1)调用设备并按拓扑要求连接
(2)配置路由器的动态路由协议
[RouterA]ripversion2multicast
[RouterA-rip]network10.0.0.0;
可以用all
[RouterA-rip]iprouting
[RouterB]ripversion2multicast
[RouterB-rip]network10.0.0.0
[Rou
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 网络工程 实验 基于 华为 路由器 交换机
![提示](https://static.bdocx.com/images/bang_tan.gif)