FANUC系统铣床与加工中心工艺编程与操作实例Word文件下载.docx
- 文档编号:18316574
- 上传时间:2022-12-15
- 格式:DOCX
- 页数:45
- 大小:702.58KB
FANUC系统铣床与加工中心工艺编程与操作实例Word文件下载.docx
《FANUC系统铣床与加工中心工艺编程与操作实例Word文件下载.docx》由会员分享,可在线阅读,更多相关《FANUC系统铣床与加工中心工艺编程与操作实例Word文件下载.docx(45页珍藏版)》请在冰豆网上搜索。
(2)外轮廓加工程序
○0002;
G91G28ZO;
G00X-62.0Y52.0M08;
G01Z-9.0F52;
G41D02G01X-40.0Y30.0F52;
G01X-20.0Y30.0;
X30.0;
G02X40.0Y20.0R10.0;
G01Y-20.0;
G02X30.0Y-30.0R10.0;
G01X-30.0;
G02X-40.0Y-20.0R10.0;
G01Y10.0;
G03X-20.0Y30.0R20.0;
G40G01X-62.0Y52.0;
粗加工时,选用Φ20的立铣刀,刀具号为T02,刀具半径补偿号为D02,补偿值为10.2mm(0.2mm是精加工余量)。
精加工时,选用Φ12的立铣刀,刀具号为T03,刀具半径补偿号为D03,补偿值为6mm。
单元三内轮廓零件加工
课题一槽加工
图3—1—1槽加工任务图
(1)十字槽粗加工程序
G90G40G21G17G94;
G90G54M3S480;
G00X30.0Y0;
G01Z-4.0F40;
X-30.0F60;
Z-8.0F40;
X30.0F60;
X0Y25.0;
Y-25.0;
Y25.0F60;
G00Z5.0M09;
(2)十字槽精加工程序
(主程序)
G90G40G21G94G17;
G90G54M3S800;
G00X0Y0;
G01Z0F40;
M98P0003L02;
G90G00Z5.0M09;
○0003;
(子程序)
G91G01Z-4.0F40;
G90G41D03G01X12.5Y7.5F50;
G02X7.5Y12.5R5.0;
G01Y25.0;
G03X-7.5R7.5;
G01Y12.5;
G02X-12.5Y7.5R5.0;
G03Y-7.5R7.5;
G01X-12.5;
G02X-7.5Y-12.5R5.0;
G01Y-25.0;
G03X7.5R7.5;
G01Y-12.5;
G02X12.5Y-7.5R5.0;
G01X30.0;
G03Y7.5R7.5;
G01X12.5;
G40G01X0Y0;
M99;
课题二型腔加工
图3—3—1型腔加工任务图
(1)型腔内粗加工程序
G01Z0F50;
M98P0002L02;
G90G01X7.0Y0F48;
G03I-7.0J0;
G01X19.0Y0;
G03I-19.0J0;
G01X0Y0F100;
(2)型腔内轮廓精加工程序
G00X5.0Y0;
G01Z0F80;
M98P0004L02;
○0004;
G91G01Z-4.0F80;
G90G41D01G01X20.0Y-15.0F48;
G03X35.0Y0R15.0;
G01Y6.7157;
G03X28.3333Y16.1438R10.0;
G02X16.1438Y28.3333R20.0;
G03X6.7157Y35.0R10.0;
G01X-6.7157;
G03X-16.1438Y28.3333R10.0;
GO2X-28.3333Y16.1438R20.0;
G03X-35.0Y6.7157R10.0;
G01Y-6.7157;
G03X-28.3333Y-16.1438R10.0;
G02X-16.1438Y-28.3333R20.0;
G03X-6.7157Y-35.0R10.0;
G01X6.7157;
G03X16.1438Y-28.3333R10.0;
G02X28.3333Y-16.1438R20.0;
G03X35.0Y-6.7157R10.0;
G01Y0;
G03X20.0Y15.0R15.0;
G40G01X5.0Y0;
单元四孔加工
课题一钻孔、攻丝加工
图4—1—1孔类零件加工任务图
M06T1;
G90G17G49G21G94;
G54M3S1200;
G00X20.0Y100.0M08;
G43H01G00Z50.0;
G99G81X-15.0Y65.0Z-4.0R5.0F80;
G98X-30.0;
G00X-120.0;
Y15.0;
G99G81X-85.0Y15.0Z-4.0R5.0F80;
G98X-70.0;
G91G28Z0M09;
M06T02;
G90G49G54M3S550;
G43H02G00Z50.;
G99G73X-15.0Y65.0Z-20.0R5.0Q2.0F60;
G99G73X-85.0Y15.0Z-20.0R5.0Q2.0F60;
M06T03;
G90G49G54M3S500;
G43H03G00Z50.;
G98G83X-30.0Y65.0Z-21.0R5.0Q2.0F60;
G98G83X-70.0Y15.0Z-21.0R5.0Q2.0F60;
M06T04;
G90G49G54M3S450;
G43H04G00Z50.;
G98G81X-15.0Y65.0Z-21.0R5.0F50;
G98G81X-85.0Y15.0Z-21.0R5.0F50;
M06T05;
G90G49G54M3S350;
G43H05G00Z50.0;
G99G82X-15.0Y65.0Z-6.0R5.0P2000F60;
G99G82X-85.0Y15.0Z-6.0R5.0P2000F60;
M06T06;
G90G49G54M3S50;
G43H06G00Z50.0;
G98G85X-30.0Y65.0Z-18.0R5.0F40;
G98G85X-70.0Y15.0Z-18.0R5.0F40;
M06T07;
G90G49G54M3S100;
G43H07G00Z50.0;
G98G84X-15.0Y65.0Z-19.0R5.0F175;
G98G84X-85.0Y15.0Z-19.0R5.0F175;
课题二镗孔加工
图4—2—1零件加工任务图
M06TO1;
G90G94G49G17G40G21;
G54M03S400;
G43H01G00Z50.0M08;
X-46.0Y55.0;
G01Z-4.0F80;
Y-55.0F60;
X46.0F1000;
Y55.0F60;
G41D01G01X17.321Y30.0F60;
X34.641Y0;
X17.321Y-30.0;
X-17.321;
X-34.641Y0;
X-17.321Y30.0;
X-20.0;
G40G01X65.0Y55.0F300;
G90G54G49G40M03S1200;
G43H03G00Z50.0M08;
G98G81X0Y0Z-4.0R5.0F60;
G90G54G49G40M03S500;
G43H04G00Z50.0M08;
G98G81X0Y0Z-20.0R5.0F60;
G28X0Y0;
G90G54G49G40M03S350;
G43H05G00Z50.0M08;
G98G73X0Y0Z-22.0R5.0Q2.0F50;
G90G54G49G40M03S250;
G43H06G00Z50.0M08;
G98G73X0Y0Z-25.0R5.0Q2.0F45;
G90G54G49G40M03S200;
G43H07G00Z50.0M08;
G98G73X0Y0Z-26.0R5.0Q2.0F40;
G90G54G49G40M03S800;
G43H02G00Z50.0M08;
X46.0Y55.0;
G41D02G01X17.321Y30.0F60;
X-17.321Y30.0;
M06T08;
G43H08G00Z60.0M08;
G98G85X0Y0Z-17.0R5.0F60;
M06T09;
G90G54G49G40M03S1500;
G43H09G00Z60.0M08;
G98G85X0Y0Z-17.0R5.0F50;
单元五综合课题加工
课题一镜像加工
图5—1—1加工任务图
G50.1X0Y0
G90G54M3S680;
M08
M98P0002
G51.1X0
G50.1X0
M09
M30
G00X-58.0Y-48.0;
Z50.0;
G01Z-3.0F50;
G41D01G01X-47.0Y-45.0F100;
X-47.0Y-20.0;
X-37.0Y-20.0;
G03X-27.0Y-10.0R10.0;
G01X-27.0Y10.0;
G03X-37.0Y20.0R10.0;
G01X-47.0Y20.0;
X-47.0Y42.5;
X-28.0Y42.5;
G02X-8.0Y22.5R20.0;
G01X-8.0Y-20.0;
X-30.5Y-42.5;
X-50.0Y-42.5;
G40G01X-58.0Y-48.0;
G00Z50.0;
课题二极坐标加工
图5—2—1加工任务图
G54G40;
M08;
G15;
M03S700;
G00X58.0Y-10.0;
G01Z-5.0F50;
G41D01G16G01X36.0Y-5.0F100;
G02X24.0Y-5.0R6.;
G03X24.0Y275.0R-24.0;
G02X36.0Y275.0R6.0;
G02X36.0Y-5.0R-36.0;
G40G15G01X58.0Y-10.0;
G00Z150.0;
M09;
课题三旋转加工
图5—3—1加工任务图
G69;
G68X0Y0R30.0;
Z50.0M08;
G41D01G01X25.0Y10.0F100;
G03X15.0Y20.0R10.0;
G01X-15.0;
G03X-25.0Y10.0R10.0;
G01Y-10.0;
G03X-15.0Y-20.0R10.0;
G01X15.0;
G03X25.0Y-10.0R10.0;
G01X25.0Y10.0;
G00Z150.0M09;
课题四综合零件的加工
图5—4—1加工任务图
(1)正六边形加工程序
G90G54M03S400;
G00X0Y55.0;
G01Z-6.F60;
G41D01G01X0Y29.0F100;
X10.97;
G02X19.63Y24.0R10.0;
G01X30.60Y5.0;
G02Y-5.0R10.0;
G01X19.63Y-24.0;
G02X10.97Y-29.0R10.0;
G01X-10.97;
G02X-19.63Y-24.0R10.0;
G01X-30.60Y-5.0;
G02Y5.0R10.0;
G01X-19.63Y24.0;
G02X-10.97Y29.0R10.0;
G01X0;
G40G01X0Y55.0;
G00Z50.0M09;
(2)斜六边形加工主程序
G90G40G21G17G94G69;
G90G68X0Y0R10.0;
M98P0003;
G00X0Y40.0;
G01Z-4.F60;
G41D01G01X0Y25.0F100;
G02X16.17Y22.0R6.0;
G01X27.14Y3.0;
G02Y-3.0R6.0;
G01X16.17Y-22.0;
G02X10.97Y-25.0R6.0;
G02X-16.17Y-22.0R6.0;
G01X-27.14Y-3.0;
G02Y3.0R6.0;
G01X-16.17Y22.0;
G02X-10.97Y25.0R6.0;
G40G01X0Y40.0;
(3)凹槽加工程序
G54M03S680;
GO0X60Y-50;
M98P0005;
G51.1X0Y0;
G50.1X0Y0;
G0Z100.0M09;
○0005;
G00X56.0Y-46.0;
G41D04G01X52.34Y-33.55F;
X34.88Y-19.58;
G3X26.76Y-29.73R6.5;
G1X41.94Y-41.87;
G40G01X56.0Y-46.0;
(4)孔加工程序
○0006;
G90G40G21G17G94G15;
G54M03S1500;
GO0X0Y0;
G43H05G00Z20.0;
G16G00X40.0Y40.0;
G99G81Z-9.0R5.0F60;
G00X40.0Y210.0;
G98G81Z-9.0R5.0F60;
G90G15G54M3S500;
G43H06G00Z20.0;
G99G81Z-20.0R5.0F60;
G98G81Z-20.0R5.0F60;
G90G15G54M03S450;
G43H07G00Z20.0;
G99G81Z-20.0R5.0F50;
G98G81Z-20.0R5.0F50;
G90G15G54M03S500;
G43H08G00Z20;
G99G82Z-10.0R5.0P2000F60;
G90G15G54M03S50;
G43H09G00Z20.0;
G99G85Z-18.0R5.0F40;
G00X40.0Y210.0
G98G85Z-18.0R5.0F40;
数控编程实例
1.根据图样要求、毛坯及前道工序加工情况,确定工艺方案及加工路线
1)以已加工过的底面为定位基准,用通用台虎钳夹紧工件前后两侧面,台虎钳固定于铣床工作台上。
2)工步顺序
①铣刀先走两个圆轨迹,再用左刀具半径补偿加工50㎜×
50㎜四角倒圆的正方形。
②每次切深为2㎜,分二次加工完。
2.选择机床设备
根据零件图样要求,选用经济型数控铣床即可达到要求。
故选用XKN7125型数控立式铣床。
3.选择刀具
现采用φ10㎜的平底立铣刀,定义为T01,并把该刀具的直径输入刀具参数表中。
4.确定切削用量
切削用量的具体数值应根据该机床性能、相关的手册并结合实际经验确定,详见加工程序。
5.确定工件坐标系和对刀点
在XOY平面内确定以工件中心为工件原点,Z方向以工
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FANUC 系统 铣床 加工 中心 工艺 编程 操作 实例
![提示](https://static.bdocx.com/images/bang_tan.gif)