SZ型省能型风机《产品说明书》Word文件下载.docx
- 文档编号:18248965
- 上传时间:2022-12-14
- 格式:DOCX
- 页数:35
- 大小:347.28KB
SZ型省能型风机《产品说明书》Word文件下载.docx
《SZ型省能型风机《产品说明书》Word文件下载.docx》由会员分享,可在线阅读,更多相关《SZ型省能型风机《产品说明书》Word文件下载.docx(35页珍藏版)》请在冰豆网上搜索。
I.SUMMARY
Ⅱ.SPECIFICATIONS
Ⅲ.CONSTRUCTION
Ⅳ.TECHNOLOGICALCALCULATION
Ⅴ.INSTALLATIONANDADJUSTMENT
Ⅵ.RUNNINGANDOPERATION
Ⅶ.MAINTENANCE
Ⅷ.SCOPEOFSUPPLY
Ⅸ.ATTACHMENTDOCUMENTS
一、产品概述
SZ型省能型轴流通风机是常熟市鼓风机有限公司积累几十年来消化吸收国内外先进技术而精心研制开发的新一代节能风机。
它具有的规格和性能参数不仅满足纺织企业空调系统,同时也满足工业建筑和其它中低压通风排气要求。
经实际运行测定节电达15~25%。
二、产品规格
系列风机的机号有№8、9、10、11.2、12.5、14、16、18、20等共九种,不同机号的叶片数有8、10两种,叶片可安装成各种不同角度,各机号风机有A式(直联传动)和C式(皮带传动)二种,C式性能与A式相同。
各机号风机根据用户要求可配扩散筒。
风机性能见各机号轴流通风机性能及配套件表。
各机号风机及扩散筒外形及安装尺寸分别见附图。
三、产品结构
本风机主要由集风器、壳体、叶轮和机架组成。
叶轮结构简单、安装维修方便。
叶片为机翼型扭曲叶片,叶片材质为ZL104高强度铸造铝合金,并经表面抛光和硬质氧化处理,叶片表面硬度高,耐腐蚀性能好、使用寿命长。
电动机容量根据不同的风压风量而配(详见性能及配套件表)。
本系列风机安装方式可分墙式(Q型)安装和落地式(L型)安装,应在订货时注明。
同时亦须注明风机的使用条件是压入式还是吸入式,以便组装供货。
四、工艺计算
本风机所列性能参数是指在标准进气状态的空气性能。
标准进气状态指压力为101325N/m2、温度为20℃,相对湿度为50%、空气密度为1.2kg/m3。
如用户的使用条件改变,可按下列公式进行换算。
流量Q=Q0
全压P=P0(
)2
功率N=N0(
)3
式中:
Q0——性能表中的流量m3/s
P0——性能表中的全压Pa
N0——性能表中的功率(计算理论功率)kW
ρ0——空气密度1.2kg/m3
Q——使用条件下所产生的流量m3/s
P——使用条件下所产生的全压Pa
N——使用条件下所需理论功率kW
ρ——使用条件下的空气密度kg/m3
五、风机的安装与调试
5.1墙式安装风机:
在主机机壳外装上安装支架,把主机机壳放人墙壁上预留的空间位置(见图2),此部分表面应打毛,使混凝土牢固粘结。
应在墙上预留的空间位置先预埋入钢筋架,机壳放入后在电机座板上校水平,再把安装支架与钢筋架焊住后浇注混凝土,施工时应防止机壳变形。
待混凝土凝固后,装人电动机和叶轮,准确地定中心。
5.2落地式安装风机:
基础平整,预埋地脚螺栓,机架放稳后用螺母紧固。
5.3叶轮的安装:
先用螺丝刀头部嵌入锥度定紧套上铣开的缺口处,将定紧套安装于电动机轴上。
再把叶轮套在定紧套上,如图1所示位置,然后用3只内六角螺钉及3只弹簧垫圈通过轴盘上的紧固孔(光孔)旋入定紧套上的螺孔,叶轮即可紧固于电动机轴上。
再在电机轴端用六角螺栓及弹簧垫圈紧固轴端挡圈。
图1叶轮与电机轴头装配图
如要卸下叶轮,则先卸下轴端挡圈,再旋出所有紧固的螺钉后,旋入轴盘上的拆卸孔(螺孔)即松开叶轮,然后将之卸下。
5.4要注意检查叶轮上各连接部件有无松动,叶片与机壳间隙均匀,不得相碰。
六、风机的操作运转
6.1安装完毕后,用手扳动叶轮,检查叶轮与机壳有无碰撞现象。
点动电机检查叶轮旋转方向是否与旋向标志相符,然后进行机械运转(运转时间不少于3分钟),检查锥度定紧套上螺钉有无松动。
如运转情况良好,再在正常工况上(规定的压力与流量)连续运转(不少于4小时),如无异常现象,才允许正式使用。
6.2使用前应注意检查各连接螺栓是否拧紧,以免发生事故。
6.3使用时,风机如有异常现象应立即停车检查,修复后经试转正常后方可使用。
6.4发现下列情况之一,应紧急停车。
(1)风机或电机,突然产生剧烈振动。
(2)风机或电机的体内有异常杂音。
(3)电机机壳温度及电流突然上升,并超过规定值。
6.5注意:
当通风机起动时,任何人都不得靠近叶轮。
七、风机的维护保养
7.1经常检查固定叶片用的螺母的紧固程度,防止叶片松动。
7.2叶片如需拆卸安装时,应对号人座,不得随意安装和改变原安装角,否则将破坏风机的平衡及电动机功率不匹配。
八、单机成套供应范围
8.1№8~20轴流通风机一台(是否带扩散筒,在订货时注明)。
8.2电动机一台(根据用户需要代订,不附启动器、开关、仪表等设备)。
8.3可根据用户需要,单独供应叶轮部件(配用定紧套在订货时注明)。
8.4随机附件(见附件箱明细表)。
九、随机技术文件
9.1产品说明书1份
9.2合格证明书1份
9.3装箱单1份
Ⅰ.Application
SZ-typeenergy-savingAxialFanisanext-generationenergy-efficientfanbyChangshufanwhichdigestionandabsorptionofadvancedtechnologyfordecadesathomeandabroad.Ithasthespecificationsandperformanceparameterstomeetthetextileenterprisesnotonlyair-conditioningsystems,aswellasindustrialbuildingsandotherrequirementsinthelow-pressureexhaustventilation.Theenergy-savingisupto15%-25%
Ⅱ.Specifications
Theserialfanincludes9numbers,suchas№8、9、10、11.2、12.5、14、16、18and20.Foreachserialfannumber,areprovided8and10bladeswhicharesetbydifferentangle.ThefansareclassifiedaskindA(direct-drive)andkindC(belt-drive).TheperformanceofAisthesameasthatofC.Thediffusercanbedeliveredifrequired.
Thespecificationsandperformancesofthefansarelistedinthetablesof“SpecificationsandComplementaryParts”.
Theoveralldimensionoffananddiffuserseecorrespondingdiagrespectively.
Ⅲ.Construction
Thefanconsistsofanbellmouth,housing,impeller,adiffuser.
Thestructureoftheimpellerisofsimple,sotheinstallationandmaintenancecanbedoneeasily.Thebladeisofawing-shapetwistone.ItismadeofZL104highstrengthcastaluminumalloyandistreatedbythehardeningandoxidizingsurfaceprocess.Itfeatureshardsurface,finecorrosionresistanceandalongservicelife.Thecapacityofthemotorcanbeselectedaccordingtothedifferentairpressureandairflow(SeeTable“SpecificationsandComplementaryParts”).
Theserialfancanbeinstalledbytwoways,i.e.wall-mounted(TypeQ)andground-mounted(TypeL),soitshouldbenotedwhenordering,andatthesametime,theapplicationtermofthefanshouldnotedbyuser,whetheritisinneedsofpress-inmodeorsuctionmode(SeeDiag.4),sothatitmaybeproducedanddeliveredbyourfactoryaccordingtoyourorder.
Ⅳ.TechnologicalCalculation
Thefanperformanceparameterslistedherereferstoairperformanceinthestandardatmosphericstate.
Thestandardatmosphericstateshasthefollowingasitsparameters
Pressure:
101325N/m2
Temperature:
20℃
Relativehumidity:
50%
Airdensity:
1.2kg/m3
Iftheoperationalconditiononthepartofcustomerchanges,thedataconversioncanbecarriedoutinaccordancewiththefollowingformulas:
Flow:
Q=Q0n/n0(m3/s)
P=P0(n/n0)2(ρ/ρ0)(Pa)
Power:
N=N0(n/n0)3(ρ/ρ0)(kW)
inwhich:
Q0——“Flow”listedintheperformanceTable(m3/s)
Q——“Flow”undertheoperationalcondition(m3/s)
P0——"
Pressure”listedintheperformancetable(Pa)
P——“Pressure”undertheoperationalcondition(Pa)
N0——“effectivepower”ifthereisn’tthiscolumn,thedataconversioncanbecarriedoutaccordingtoN0=P0Q0/1000(kW)
N——“effectivepower”undertheoperationalcondition(kW)
ρ0——“Airdensity”inthestandardatmosphericstateρ0=1.2kg/m3
ρ——“airdensity”undertheoperationalcondition(kg/m3)
Ⅴ.InstallationandAdjustment
5.1.wall-mountedInstallation
Setupthemountingsupportontothecasingandmakethecasingenterthemountinglocationpreparedonthewallinadvanceandthenensureitlevling(SeeDiag.2).weldmountingsupportwiththesteelframepresetinthewall.Pourconcreteontofoursidesofcasingandatthesametimebeattentiontokeepthecasinginshape.Afterplastered,assembletheimpellerandthemotor,thencentreitexactly.
5.2.Ground-mountedInstallation
Levelthefoundation,Presetbasebolts.Mountthecasingandtightenitwithnuts.
5.3.Assembletheblades
Firstinsertascrewdriverintotaperholdingcaseandsetupthetaperholdingcaseontheshaftofmotor.Thenmountandtightentheimpellerontheholdingcase(SeeDiag.1)with3interhexagonalscrewsandspringwashersforscrewing-inthefasteningholes(throughhole).Bysodoing,theimpellerisfixedontheshaftofmotor.Atlast,pressshaftretainerwiththehexagonalboltandwasher.
Diag.1AssemblyDrawingofimpellerwithmotorshaftend
Thedisassemblingwaysareasfollowings:
Firstdisassemblethelockringlocatedintheshaftendandloosenandtakeoutallfasteningscrews.Thenturndowntheabovementionedscrewsintothedisassemblinghole(screwedhole)locatedinthebosstolossentheimpeller.Lastlyremovetheimpeller.
5.4.Checktheconnectingpartsoftheimpellerwhethertheyaresecureornot.Makesurethatthebladesareoutoftouchwiththecasingofthefanandtheclearancebetweenthebladesandthecasingisuniform.
Ⅵ.RunningandOperation
6.1.Afterinstallation,movethebladeswithhandandmakesurethatthebladesareoutoftouchwiththecasing.trystartingandensurethattherotatingdirectionoftheimpellerisnormalandproperwiththerotatingarrow.Thenletthefanrunfornotlessthan30minutes,andcheckwhetherthescrewslocatedonthetaperholdingcaseareloose.Ifitrunssatisfactory,letitrununderthenormalterms(underthenormalpressureandflow)continuouslyfornotlessthan4hours.Onlywhenthereisnoabnormalappearance,thefancanbeputintooperation.
6.2.Beforestaring,checkandensurethatalltheconnectingbolts,tightenedtoavoidfailure.
6.3.Intheoperation,anyabnormalaccidentoccurs,stopthefanimmediatelyanddonotstartituntilrepair.
6.4.Intheoperation,oneofthefollowingaccidentsoccurs,stopthefanbythebrakesurgently.
(a)Thefanorthemotorviolentlysuddenly.
(b)Anabnormalstrikingnoisesoundsfromthefanorthemotor.
(c)Thetemperatureofmotorcaseandthecurrentrisessuddenlyandexceedsvaluesspecified.
6.5.Note:
Inoperationofthefan,anyonemustnotbeneartheimpeller.
Ⅶ.Maintenance
7.1.Checkandensurethetightnessofthescrewsandnutslocatedinbladestopreventthebladesfromloosing.
7.2.Assembleanddisassemblethebladesaccordingtoitsnumber.Thebladescan’tbeassembledcasually.Thesettingangleofthebladescan'
tbeexchangedarbitrarilyforfanbalanceandmotorpowernotdestroyed.
Ⅷ.ScopeofSupply
8.1.For№8-20,Axialfan1set(withorwithoutdiffuser,accordingtoyourorder).
8.2.Motor-1set(dependingonyourorder.Themotoriswithoutstarter,switchandinstruments).
8.3.Theimpellercanbedeliveredseparatelyaccordingtotheorder(withholdingsleeve,accordingtoyourorder).
8.4.Attachmentparts(SeeListsoftheSpareParts).
Ⅸ.AttachmentDocuments
9.1.User'
sManual1Copy
9.2.CertificateofQuality1Copy
9.3.PackingLists1Copy
SZ№8轴流通风机性能及配套件表
SpecificationsandComplementaryPartsoftheSZ№8AxialFan
转速:
n=1460转/分叶片数:
10
Rotatingspeed:
n=1460r/minNumberofblades:
10
叶片安装角
Settingangle
ofblade
序号
Serial
№
全压
Totalpressure
(Pa)
流量
Flow
(m3/s)
全压效率
efficiency
η
选用电动机
OptionalMotor
型号
Type
功率
Power(kW)
14°
1
110
5.9
72
Y100L1-4
2.2
2
220
4.7
84
3
280
3.6
75
16°
140
7.2
Y100L2-4
240
6.1
300
18°
200
8.1
Y112M-4
4
310
6.9
350
SZ№9轴流通风机性能及配套件表
SpecificationsandComplementaryPartsoftheSZ№9AxialFan
Totalpressureefficiency
12°
9.1
260
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 产品说明书 SZ 型省能型 风机