中兴OMP调试指导书Word格式文档下载.docx
- 文档编号:15243135
- 上传时间:2022-10-28
- 格式:DOCX
- 页数:10
- 大小:119.07KB
中兴OMP调试指导书Word格式文档下载.docx
《中兴OMP调试指导书Word格式文档下载.docx》由会员分享,可在线阅读,更多相关《中兴OMP调试指导书Word格式文档下载.docx(10页珍藏版)》请在冰豆网上搜索。
图352创建ompcfg.ini文件
弹出如图353所示对话框,选择OMP功能类型,若iBSC为单框配置且OMP和CMP功能能均由此OMP来完成请选择“OMP+CMP+SMP”,否则选择“OMP”
图353选择omp功能类型
1.3串口配置OMP。
连接OMP的调试串口(一般为RMPB板下面的DEBUG2-232口)到调试计算机的串口,这里的调试计算机可以是OMC网管客户端。
运行操作系统自带的超级终端程序,在[连接描述]对话框中输入新建的连接名称,并为该连接选择图标,如图354所示。
图354超级终端连接描述对话框
2.单击<确定>后弹出[连接到]对话框,选择与前台实际相连的串口(本例为COM1口与前台相连),单击<确定>进行确认。
如图355所示。
图355超级终端连接到对话框
3.在弹出的[COM1属性]对话框中,单击<还原为默认值>按钮后,单击<确定>进行确认,如图356所示。
图356超级终端COM1属性
4.进入超级终端之后,在出现如“Pressanykeytostopauto-boot...”的提示时,快速按任意键停止自动启动,开始配置OMP参数。
下面是配置交互过程的打印,其中加粗的斜体字为键盘输入内容。
VxWorksSystemBoot
Copyright1984-2002WindRiverSystems,Inc.
CPU:
PCPENTIUM3
Version:
VxWorks5.5.1
BSPversion:
1.2/3
Creationdate:
Oct132005,18:
37:
29
ZZ
BootVersion:
1.08
BootBuild:
43
BootBSPVer:
0302.0700
Creationdate:
23
Pressanykeytostopauto-boot...
2\\快速按下任意键,进入串口调试模式
[BSP]BOOTMenuOperationMonitorTaskStarting(MAX:
120Second)...
+-----------------------------------------------------------------+
|BOOTPASSWORDNOTICE||-----------------------------------------------------------------|
|1.PasswordString:
3GPLAT(CASENOTSENSITIVE)||2.InputTimeout:
120Seconds,orelseReboottheBoard|
|3.MaxInputRetry:
5Times,orelseBootingbypassbootmenu|
BootPassword(3GPLATor3gplat)->
3gplat\\输入boot的密码
[BSP]KillMonitorTask[tBootMoni]Successfully!
BootModeSelectionasfollow:
0-Autoboot(bootandgetversionfromomp)
1-ConfigMPnetparameters(onlyforOmpandCmp)
2-Initializeflash(loadflashdeviceandinitfilesystem)
3-Eraseallflash(alldataonflashwillbelost)
4-Cloneflash(cloneflashtohostimagefile)
5-Restoreflash(Restoreflashfromhostimagefile)
6-Downloadfrompc(downvxworksfrompctoflash)
7-Downloadselftestprogram(downtestprogramfrompctoflash)
8-Runrelease(runthevxworksonflashdownbyoperaion6)
9-Runtheselftestprogramonflashdownbyoperation7
r-Returntotheoriginalvxworksmenu
?
-Printthishelplist
[3GPlatBoot]:
1\\进入配置OMP参数模式
************Init**********
Thisistwocascade32MDiskOnChipMillenniumPlusChip-G2
CreattffsdeviceforDOC
/DOC0/-diskcheckinprogress...initialized.
dosChkLib:
CLOCK_REALTIMEisbeingresettoFRIOCT2808:
38:
542005
Valueobtainedfromfilesystemvolumedescriptorpointer:
0x36a9cc
TheoldsettingwasTHUJAN0100:
00:
011970
AcceptedsystemdatesaregreaterthanTHUDEC2700:
001990
/DOC0/-VolumeisOK
total#ofclusters:
31,929
#offreeclusters:
13,861
#ofbadclusters:
0
totalfreespace:
27,722Kb
maxcontiguousfreespace:
25,595,904bytes
#offiles:
39
#offolders:
5
totalbytesinfiles:
36,070Kb
#oflostchains:
totalbytesinlostchains:
FlashVerDir/DOC0/VER/alreadyexist!
Configselection:
1-SetOmp(orCmp)'
sOmcIpandMac!
2-SetOmpBootParas!
3-SetOMPBootType!
4-SetNet_ElementBureauNo.!
5-Quitconfig,returntobootmenu!
6-printthishelplist
Enteryourselection(1/2/3/4/5):
1\\进入模式1,设置OMP的IP和MAC地址
PleaseenterIp(mayincludenetmask)indottednotationas,suchas129.0.0.1:
ff0
00000!
[EnterOMP'
sOMCIpaddress]:
129.0.31.12\\OMPIP地址,根据实际规划进行输入
OMP'
sOMCIpnetmaskissetdefaultvalue0xFF000000!
OMP'
sOMCIpis:
129.0.31.12!
sOMCIpnetmaskis:
0xFF000000!
0x81001f0c!
0xff000000!
Writeflashbootcfg.inifilesucc!
PleaseenterMacindotteddecimalnotationas,suchas10.10.10.10.10.10!
sOMCMacaddress]:
\\输入OMP单板发货时单板上MAC地址标签标记所规定的地址或者直接回车(系统默认)
Inputisnull,nothingdone!
PleaseenterGatewayIp(Notincludenetmask)indottednotationas,suchas0.0.0.0!
sGatewayIpaddress]:
\\直接回车
Inputisnull,0isset!
PleaseenterOMCServerIp(Notincludenetmask)indottednotationas,suchas0.0.0.0!
[EnterOMCServerIpaddress]:
\\直接回车
2\\进入模式2,设置OMP启动参数
PleaseenterIp
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 中兴 OMP 调试 指导书