路由器和交换机的RIPMD5明文认证Word格式文档下载.docx

路由器和交换机的RIPMD5明文认证Word格式文档下载.docx

《路由器和交换机的RIPMD5明文认证Word格式文档下载.docx》由会员分享，可在线阅读，更多相关《路由器和交换机的RIPMD5明文认证Word格式文档下载.docx（10页珍藏版）》请在冰豆网上搜索。

RA_config#intgigaEthernet0/3

RA_config_g0/3#ipaddress192.168.1.1255.255.255.0

RA_config_g0/3#noshutdown

RA_config_g0/3#exit

在RB上配置基础信息

enable

Router#config

Router_config#hostnameRB

RB_config#intgigaEthernet0/3

RB_config_g0/3#ipaddress192.168.1.2255.255.255.0

RB_config_g0/3#noshutdown

RB_config_g0/3#exit

RB_config#intfastEthernet0/0

RB_config_f0/0#ipaddress192.168.2.2255.255.255.0

RB_config_f0/0#noshutdown

RB_config_f0/0#exit

在RSW1上配置基础信息

DCRS-5650-28（R4）>

DCRS-5650-28（R4）#config/进入配置模式

DCRS-5650-28（R4）（config）#hostnameRSW1/更改设备名称

RSW1（config）#vlan100/创建vlan100

RSW1（config-vlan100）#exit/退出

RSW1（config）#intethernet1/0/1/进入端口

RSW1（config-if-ethernet1/0/1）#switchportaccessvlan100

SettheportEthernet1/0/1accessvlan100successfully

【将该端口填加到vlan100】

RSW1（config-if-ethernet1/0/1）#exit/退出

RSW1（config）#interfacevlan100/进入vlan100

RSW1（config-if-vlan100）#ipaddress192.168.0.1255.255.255.0

RSW1（config-if-vlan100）#exit/退出

RSW1（config）#exit

RSW1#

RSW1#ping192.168.0.2

Type^ctoabort.

Sending556-byteICMPEchosto192.168.0.2,timeoutis2seconds.

!

Successrateis100percent（5/5）,round-tripmin/avg/max=0/3/16ms

这时候测试一下，ping路由器连接交换机的口的IP地址，肯定能ping通，ping不通就代表你配置错了，或者没插线，或者网线坏了

enable

DCRS-5650-28（R4）#config

DCRS-5650-28（R4）（config）#hostnameRSW2

RSW2（config）#vlan200

RSW2（config-vlan200）#exit

RSW2（config）#intethernet1/0/1

RSW2（config-if-ethernet1/0/1）#switchportaccessvl200

SettheportEthernet1/0/1accessvlan200successfully

RSW2（config-if-ethernet1/0/1）#exit

RSW2（config）#interfacevlan200

RSW2（config-if-vlan200）#ipaddress192.168.2.1255.255.255.0

RSW2（config-if-vlan200）#exit

RSW2（config）#exit

RSW2#ping192.168.2.2

Sending556-byteICMPEchosto192.168.2.2,timeoutis2seconds.

设置RIP动态路由

RSW2（config）#routerrip/启用RIP协议

RSW2（config-router）#ver2/版本号为ver2

RSW2（config-router）#showiproute/查看路由表

Codes:

K-kernel,C-connected,S-static,R-RIP,B-BGP

O-OSPF,IA-OSPFinterarea

N1-OSPFNSSAexternaltype1,N2-OSPFNSSAexternaltype2

E1-OSPFexternaltype1,E2-OSPFexternaltype2

i-IS-IS,L1-IS-ISlevel-1,L2-IS-ISlevel-2,ia-IS-ISinterarea

*-candidatedefault

C127.0.0.0/8isdirectlyconnected,Loopbacktag:

C192.168.2.0/24isdirectlyconnected,Vlan200tag:

Totalroutesare:

2item（s）

RSW2（config-router）#network192.168.2.0/24/宣告网段

RSW2（config-router）#exit/退出

在RB上配置RIP动态路由

RB_config#routerrip

RB_config_rip#ver2

RB_config_rip#showiproute

C-connected,S-static,R-RIP,B-BGP,BC-BGPconnected

D-BEIGRP,DEX-externalBEIGRP,O-OSPF,OIA-OSPFinterarea

ON1-OSPFNSSAexternaltype1,ON2-OSPFNSSAexternaltype2

OE1-OSPFexternaltype1,OE2-OSPFexternaltype2

DHCP-DHCPtype,L1-IS-ISlevel-1,L2-IS-ISlevel-2

VRFID:

0

C192.168.1.0/24isdirectlyconnected,GigaEthernet0/3

C192.168.2.0/24isdirectlyconnected,FastEthernet0/0

RB_config_rip#network192.168.1.0255.255.255.0

RB_config_rip#network192.168.2.0255.255.255.0

RB_config_rip#exit

在RA上配置动态路由

RA_config#routerrip

RA_config_rip#ver2

RA_config_rip#showiproute

C192.168.0.0/24isdirectlyconnected,FastEthernet0/0

RA_config_rip#network192.168.0.0255.255.255.0

RA_config_rip#network192.168.1.0255.255.255.0

RA_config_rip#exit

在RSW1上配置RIP动态路由

RSW1（config）#routerrip

RSW1（config-router）#ver2

RSW1（config-router）#showiproute

C192.168.0.0/24isdirectlyconnected,Vlan100tag:

RSW1（config-router）#network192.168.0.0/24

RSW1（config-router）#exit

下面测试，由RSW1pingRSW2，能ping通代表路由成功了

RSW1#ping192.168.2.1

Sending556-byteICMPEchosto192.168.2.1,timeoutis2seconds.

Successr