用油漆罐自制斯特林发动机Word下载.docx
- 文档编号:14848167
- 上传时间:2022-10-25
- 格式:DOCX
- 页数:28
- 大小:1.04MB
用油漆罐自制斯特林发动机Word下载.docx
《用油漆罐自制斯特林发动机Word下载.docx》由会员分享,可在线阅读,更多相关《用油漆罐自制斯特林发动机Word下载.docx(28页珍藏版)》请在冰豆网上搜索。
下载附件(41.79KB)
斯特林发动机
Removethepaintcanlidandmarkalinearoundthesidethatisexactly5/8downfromthetop.
Markanotherlinearoundtheoutsidethatisexactly5/8”upfromthebottom.
Cutcarefullyalongthisline.
Cutcarefullysothatyoualsopreservethecentersectionofthecan.
Youaregoingtousethecentersectiontocutsomeadditionalparts.
下载附件(36.87KB)
Iuseasheetmetalnibblertocutmypaintcans.
Idrillasmallhole(about1/4”)tostartthecut,insertthenibbler,thenworkmywayaroundthecan.
下载附件(40.11KB)
Usetinsnipstocutthecenterbandofthepaintcan.
Makeaverticalcutparalleltotheweldthatisinthesideofthecan.Measureandcutastripofmetalfromthebottomofthecanthatisexactly13/16”tall.
Thiscutisparalleltothecutmadewhenyouremovedthebottomofthecan.
Thispieceofmetalwillbeusedtomakethepressurechambersidewall.
20上传
下载附件(36.66KB)
Thepressurechambersidewallwillbegluedtotheinsideofthetopandbottomcanparts.
Usethehightempsiliconeglueforthis.
Glueallthreepiecestogetheratthesametime(top,side,andbottom).
Startbygluingthesidewalltotheinsideofthepressurechambertop.
(Thetopisthepiecewiththelid.)
Useenoughsiliconetogetanairtightsealeverywhere.
Iusedasmallpieceofmetal(about1/2”x11/8”)toreinforcetheseaminthesidewall.
Setthisassemblyasideuntiltheglueiscompletelycured.
21上传
下载附件(38.59KB)
MakeaDisplacer
Thedisplaceriscutfromapieceof3/16”thickfoamcoreposterboard.
Measuretheopeningofthepaintcan.
Thedisplacerwillhavetofitintothisopening,soitmustbemadealittlesmaller.
Useacompasstomarkacircleontheposterboardthatisexactly1/8”smallerindiameterthantheopeningofthepaintcan.
Thiswillprovide1/16”clearancebetweentheedgeofthedisplacerandtheopeningofthecan.
Cutcarefullyontheline.
下载附件(32.75KB)
Cuta3”pieceof1/16”musicwire.
Theeasiestwaytocutmusicwireistoscoreitwithafileandthenbenditandbreakit.
Goodqualitymusicwireisveryhardandwillbreakliketoolsteelwhenitisscoredandbent.
Placea90degreebendinthemusicwire3/4”fromoneend.
Thisbendshouldbeascloseto90degreesasyoucangetittobe.
下载附件(95.81KB)
Ifyouhaveadrillpressyoucanuseittocreateasimplejigforgluingthedisplacerrodtothedisplacer.
Simplydrilla3/32”holethroughaflatboard.
Thisholewillholdthedisplacerrodatthecorrectanglewhiletheglueiscuring.
下载附件(18.81KB)
Pressthelongendofthedisplacerrodthroughthecenterofthedisplaceranddownthroughtheholeinthejig.
Applyenoughpressuretocompresstheposterboardjustalittlebitaroundthecenter.
Fillthedepressionwithepoxyglueandsetitasideuntilthegluehascured.
Oncethegluecuresremovetheassembledpartfromthejigandcheckthealignment.
Therodmustbeperpendiculartothesurfaceofthedisplacerandintheexactcenterofthedisk.
23上传
下载附件(29.37KB)
PreparetheDriveCylinder
Drilla7/16”holeinthecenterofthebottomofthefilmcan.
Thisholeisdrilledtofittheshortpipenipplethatisusedtoconnectthedrivecylindertothepressurechamberlid.
下载附件(47.02KB)
Drillaholeinthecenterofthelidandcarveitoutuntilitisaslargepossible,untilonlyaringremains.
Thisringwillbeusedtosealthediaphragmtothedrivecylinder.
下载附件(8.07KB)
PreparethePressureChamberLid
Useacompasstofindthecenterofthepaintcanlid.
Todothis,setthecompasstomatchtheradiusofthelid,andthenuseittodrawalinenearthecenterofthelid.
Rotatethelid90degreesandrepeattheprocess.
Continuetorotatethelidanddrawmarkswiththecompassuntilyouhaveestablishedthecenterpointofthelid.
下载附件(42.12KB)
Drilla1/4”holethroughthecenterofthelid.
Locatethepositionofthedrivecylinder.
Thedrivecylinderwillbepositionedasclosetotheedgeofthelidaspossiblewhilestillbeingmountedtotheflatsurfaceofthelid.
Markthepositionoftheholeusingthefilmcanasaguide.
Drilltheholewitha7/16”drillbit.
下载附件(37.3KB)
MakeandAttachthePressureChamberGland
The“gland”allowsthedisplacerrodtopassthroughthetop
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 油漆 自制 斯特林 发动机
![提示](https://static.bdocx.com/images/bang_tan.gif)