无损检测工艺规程液体渗透模板Word文档下载推荐.docx
- 文档编号:13880796
- 上传时间:2022-10-14
- 格式:DOCX
- 页数:14
- 大小:119.62KB
无损检测工艺规程液体渗透模板Word文档下载推荐.docx
《无损检测工艺规程液体渗透模板Word文档下载推荐.docx》由会员分享,可在线阅读,更多相关《无损检测工艺规程液体渗透模板Word文档下载推荐.docx(14页珍藏版)》请在冰豆网上搜索。
PROCEDUREFORLIQUIDPENETRANTEXAMINATION
液体渗透检验工艺规程
CONTROLLED在控本□
UNCONTROLLED非在控本□
COPYNO副本编号:
PREPAREDBY编制:
DATE日期:
REVIEWEDBY审核:
APPROVEDBY批准:
DATE日期:
2of8
DEMONSTRATIONCERTIFICATION
Thisistocertifythatthisprocedurehasbeendemonstratedona
testspecimenwithknowndefectstothesatisfactionoftheAuthorized
InspectoraccordingtoASMECodeSectionV,T-150asrequiredbytheSectionⅧ
Div.1,Appendix8.
TestSpecimenNo.:
Demo.ReportNo.:
NDELevelⅢ:
AI:
3of8
1.General
1.1ThisprocedureisappliedtodyeliquidpenetrantexaminationofmetalmaterialandweldmentforASMECodeitems.
1.2Thisprocedureisonlysuitablefordetectingthedefectsthatareopentothesurfaceofmaterialorweldment.
1.3ThisprocedureshallbedemonstratedtothesatisfactionoftheAIpriortoimplementation.
2.Personnel
2.1ThepersonnelengagedinthepenetrantexaminationshallbequalifiedandcertifiedinaccordancewiththerequirementofNJBSTCo.,Ltd.’s”WrittenPracticeforNDEPersonnelTrainingExamination,QualificationandCertification”(No.:
QCD-011).
3.PenetrantMaterials
3.1Thepenetrantmaterialsisintendedtoincludeallpenetrants,solventsorcleaningagents,developers,etc,usedintheexaminationprocess.
3.2Theliquidpenetrantexaminationmaterialsshallbedesignatedandrecommended,asshowninTable3.2.Thematerialsusedforexaminationshallbethesametype.Intermixingofpenetrantmaterialsfromdifferentfamiliesordifferentmanufacturersisnotpermitted.
Table3.2
ManufacturerMaterialModel
ShanghaiPenetrantHD-RS
(ShipBrand)DeveloperHD-XS
CleaningAgentHD-BX
3.3Whenexaminingausteniticstainlesssteelortitanium,allmaterialsshallbeanalyzedindividuallyforchlorineandfluorinecontentinaccordancewiththeprocedureshowninT-641(b)ofASMECodeSectionV.Thetotalchlorineplusfluorinecontentshallnotexceed1%oftheresiduebyweight.Thecertificateofcompliancefrommanufacturershallbeobtained.
3.4Whenexaminingnickelbasealloys,allmaterialsshallbeanalyzedindividuallyforsulphurcontentinaccordancewiththeprocedureshowninT-641(a)ofSectionV.Thesulphurcontentshallnotexceed1%oftheresiduebyweight.Thecertificateofcompliancefrommanufacturershallbeobtained.
1.概述
1.1本规程适用于ASME规范产品金属材料和焊件着色液体渗透检验。
1.2本规程仅适用于探测材料或焊件表面开口类缺陷。
1.3本规程在执行之前,须演示至AI满意。
2.人员
2.1从事液体渗透检验的人员必须是根据南京定色钛业有限公司<
<
NDE人员培训、考试、资格认证实施细则>
>
(资料号:
QCD-011)进行考试和资格任命的合格人员。
3.渗透材料
3.1渗透材料包括检验过程中使用的所有渗透剂、溶剂或清洗剂、显像剂等。
3.2液体渗透探伤材料,必须是指定的和推荐的,见表3.2。
检验使用的材料必须是同一类型的。
不允许用不同类型的或不同制造厂的渗透材料混合使用
表3.2
3.3当检验奥氏体不锈钢或钛材时,必须根据ASME规范第Ⅴ卷T-641(b)中的程序,对所有材料分别分析氯和氟的含量。
残留氯和氟总含量不得超过残留物重量的1%,必须有制造厂相应的合格证。
3.4当检查镍基合金时,必须按照ASME规范第Ⅴ卷T-641(a)中的程序,对所有材料分别分析硫含量。
硫含量不得超过残留物重量的1%。
必须有制造厂相应的合格证。
4of8
4.ExaminationProcedure
4.1ExaminationFlowChartasshowninFig.4.1.
Fig.4.1
4.2SurfacePreparation
Priortoallpenetrantexamination,thesurfacetobeexaminedandalladjacentareaswithinatleast1in.(25.4mm)shallbedryandfreeofdirt,grease,lint,scale,weldingflux,weldspatter,paint,oilandotherextraneousmatter.Ifnecessary,surfaceshallbepreparedbygrindingormachining.
4.3Precleaning
4.3.1Theareastobeexaminedandadjacentareaswithinatleast1in.(25.4mm)shallbecleanedusingcleaningagentbeforethepenetrantisapplied.
4.3.2Aftercleaning,dryingofthesurfacetobeexaminedshallbeaccomplishedbynormalevaporationorwithforcedair,asappropriate.Theminimumdryingtimeshallensurethatthecleaningsolutionhasevaporatedpriortoapplicationofthepenetrant.
4.4PenetrantApplication
4.4.1Thepenetrantmaybeappliedonthesurface
4.检验程序
4.1检验程序流程图见图4.1
图4.1
4.2表面制备
所有渗透检验前,被检工件表面及其附近至少为1英寸(25.4mm)的区域内都应干燥清洗干净,不得有任何脏物、纤维屑、氧化皮、焊剂、油和其它外来物。
必要时,应对表面进行打磨或机加工。
4.3预清洗
4.3.1在施加渗透剂之前,被检区域及其附近至少为1英寸(25.4mm)的区域内均需用清洁剂进行清洗。
4.3.2清洗后,经过适当的方法(自然挥发或人工通风),对被检表面进行干燥;
最少干燥的时间以保证在施加渗透剂之前清洁剂已完全挥发为界。
4.4施加渗透剂
4.4.1能够用浸渍、涂刷或喷涂等任一合适的方法,在被检工件
5of8
ofworkpiecestobeexaminedbyanysuitablemeanssuchasdipping,b
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 无损 检测 工艺 规程 液体 渗透 模板
![提示](https://static.bdocx.com/images/bang_tan.gif)