钢管设备工艺中英文对照.docx
- 文档编号:1372159
- 上传时间:2022-10-21
- 格式:DOCX
- 页数:17
- 大小:1.52MB
钢管设备工艺中英文对照.docx
《钢管设备工艺中英文对照.docx》由会员分享,可在线阅读,更多相关《钢管设备工艺中英文对照.docx(17页珍藏版)》请在冰豆网上搜索。
钢管设备工艺中英文对照
直缝钢管生产装备与工艺介绍
中英文对照
1.直缝管生产主要装备技术简介
ERW生产线全线采用PLC自动控制。
开卷机:
双锥自动开卷,采用光电对中控制系统,可开卷重20吨;
接板机:
自动剪切对焊,前后钢卷头尾对接埋弧自动焊;
储料坑:
采用光电检测系统;
成型机:
采用目前比较先进的排辊成型方式,接近自然成型,这种成型原理是:
当带钢初成型后进入排辊成型,通过大量小直径被动排辊使钢带逐渐形成圆形,这种“自然成型方法”有以下优点:
⑴实际成型过程中,带钢边部纵向平整、无波浪、无皱
折;
⑵在圆周上得到精确的几何形状;
⑶三架精成型采用四辊万能机架,便于调整,可得到理想的几何形状;
高频发生器:
600KW高频发生器由一个PLC控制,具有焊接温度显示自动控制系统,防止火花短路系统,报警系统,即适用于感应焊,也适用于接触焊。
震荡电路有自己的柜体,该柜体积小,便于靠近焊管生产线,使高频发生器输出和感应圈之间的功率损失最小,整机输出功率高;
挤压焊接装置:
由四辊挤压和焊接顶辊完成,可方便调整挤压力和V型开口角,既能保证适当的挤压力,又能得到一个稳定的烧化和熔解的过程;
内毛刺去除装置:
由液压控制,稳定可靠,内毛刺剩余高度控制在合同规定的范围;
热处理装置:
焊缝中频常化热处理机三台(1500KW、美国),加热宽度30mm,加热效率高,保证加热深度渗透全壁厚;同时具有消除焊接残余应力作用;
定径矫直机:
采用四辊万能机架,经减径整圆,达到理想的外径公差、圆度及直度,兼有降低焊缝残余应力作用;
飞切定尺机:
采用微机控制的液压加力旋切式(四把园盘切刀)切断方式,无噪音、无铁屑消耗,对焊缝无损伤,定尺精度±3mm;
平头倒坡口机:
采用先进的液压仿型装置,微机自动控制升降台架、传输、平头、倒坡口。
管端可加工为用户要求的形状,便于用户管端对口接焊。
2.直缝管生产工艺
2.1工艺简述
准备段:
主要包括备卷、开卷、直头整平、剪切对焊、
递料、储料、拉出整平、对中、板材电磁超声波探伤等工序。
制管段:
予成型、排辊成型、精成型、五辊挤压高频焊接、去除内外毛刺、在线超声波探伤、焊缝热处理、定径、矫直飞切定尺。
精整段:
平头倒坡口、水压试验、手动超声波复检、最终检验、标识、包装。
2.2工艺流程图
SteelPipeManufacturingEquipments
andTechnologyProcess
1.LinePipeMainManufacturingEquipmentTechnology
(ERW)productionlineadoptPLCautomaticcontrolcompletely.
Uncoiler:
Double-coneuncoiler,adoptinglightand
electricitycentercontrolsystem,canuncoil20MTweight.
Coilbutting-weldingmachine:
weldingofcoilinautomaticshears,theformerendandthelaterheadisbutting-weldingbysubmergedarcwelding.
Storematerialspot:
adoptinglightandelectricalinspectionsystem.
Formingmachine:
adoptingtherelativelyadvancedstandingformingwayofrolleratpresent.It’sclosetonaturalforming.Thiskindofformingprincipleis:
Afterskelppre-formedandenterstanding-rollerform,arrangerollermakeskelpformintheroundgraduallypassivelythroughlittlediameters.Therearefollowingmeritsinthiskindof“naturalformingmethod”
⑴Inactualformingprocess,thetransverseedges
ofcoilaresmoothwithoutwave,wrinkly.
⑵Incircumferencetogettheaccurategeometry.
⑶Therefine-formingadoptfourrollersofomnipotencestand.easytoadjust,cangettheidealgeometryform.
600KWhighfrequencygeneratoriscontrolledbyonePLC.Thereistemperatureofweldingthatshowstheautomaticcontrolsystem.Itpreventsflashshortcircuitsystem,warningsystemsuitableforreactionweldandkeepingintouchweldingtoo.Oscillatingcircuithaveowncupboardbodywithlittlevolume.It’seasyclosetoweldingproductionline.Makingthehighfrequencygeneratorexportthepowerwhileenclosingwithreactiontolosetheminimum.Theoutputpowerofthecompletemachineishigh.
Extrudedweldingequipments:
It’sfinishedbyfourrollersandextrudedwelding,veryconvenienttoadjustextrusionstrengthandVtypeopening’scorner,canguaranteeproperextrusionstrength,alsogetthecourseofasteadyburningandfusion.
Theremovalequipmentsofinternalflash:
Theequipmentiscontrolledbythehydraulicpressure,It’sreliabletobesteady.Interiorburrreinforcementshallbecontrolledwithintherangestipulatedinthecontract.
Heattreatmentequipments:
Threeweldingseammid-frequencynormalizedheattreatment(1500KW,USA).Heatingwidthis30mmwithhighefficiencyandcanpenetratethewholewallthickness.Dispelweldingremainingstressfunctionatthesametime
SizingandStraighteningMachine:
Adoptingfourrollersofomnipotencestand,throughreducingdiameterandrounded,reachtheidealODtolerance,roundnessandstraightness.Reducetheremainingstressfunctionofweldingseamtoo.
Flyingcut-offdisccutter:
Adopthydraulicpressurethrustaugmentationwhocomputercontrol(fourdisccutter)cutoffthewaywithoutnoiseandscrapesabrasionandnoimperfectioninweldingseam.sizingprecision:
±3mm
Endbeveledmachine:
Adoptingadvancedhydrostaticpressureimitativedevice,computerautomaticallycontrolgoupanddowntable,transmitcrewcut,chamfer.Inchargeofaccuratefromchamferingangle:
30±(0-5)°C.Therootfaceleave:
1.6mm±0.8mm.It’sconvenienttouserconnectandweld.
2.LinePipeManufacturingProcess
2.1Brief
PreparingSection:
Includingpreparingcoil,coilopening,headleveling,shearendwelding,feedingmaterial,storingmaterial,pulling-outleveling,stripcentering,stripelectromagneticUTdetectionandsoon.
ManufacturingSection:
Pre-forming,standing-rollerforming,fin-passforming,five-rollerextrudedhighfrequencywelding,theremovalofinsideandoutsideburr,in-lineUTdetection,weldingseamheattreatment,sizing,straighteningdisccutting-off.
FinSection:
Endbeveled,hydraulicpressuretesting,manualUTre-testing,finalinspection,marking,package.
2.2TechnologicalProcess
双面埋弧焊螺旋钢管
生产装备与工艺介绍
中英文对照
一、钢卷Coil
1.外观和尺寸检验
Visual&DimensionalInspection
1.1外观检验:
钢卷表面应进行外观检验。
1.2尺寸检验:
应使用超声波测厚仪或千分尺检测钢卷的壁厚和卷尺检测钢卷的宽度。
1.3检查钢卷质证书。
1.1Visualinspection:
coilsurfacessh
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 钢管 设备 工艺 中英文 对照