模具术语 中英文翻译.docx
- 文档编号:10814657
- 上传时间:2023-02-23
- 格式:DOCX
- 页数:11
- 大小:18.12KB
模具术语 中英文翻译.docx
《模具术语 中英文翻译.docx》由会员分享,可在线阅读,更多相关《模具术语 中英文翻译.docx(11页珍藏版)》请在冰豆网上搜索。
模具术语中英文翻译
∙assemble mould 合箱
∙assembling mould 装配铸型
∙baked mould 干型
∙bar mould 多穴压模
∙big-end-up mould 上大下小钢锭模
∙black mould ofrice 黑变病
∙blank mould turnover 雏型模翻转
∙blowing mould 吹模
∙blue mould ofcitrus 柑桔青霉病
∙cap mould 压顶线脚
∙cartype mould conveyor 小车式铸型输送机
∙case mould plaster 母模用石膏
∙casting mould 铸型
∙centrifugalcasting mould 离心铸造铸型
∙ceramic mould casting 陶瓷模注法
∙channel mould 槽模
∙chill mould 冷铸型(模)
∙close mould 封闭铸型
∙close mould (铸造用) 合箱
∙closed mould 闭式模;闭式压模
∙cold-punching mould 冷冲模
∙collapsible mould 分室模
∙compositeceramic mould 复合陶瓷型
∙composite mould casting 复合型铸造
∙copper mould base 铜模底
∙copper mould wall 铜坩埚壁
∙corrugated mould 波形铸模
∙cover mould 压缝线脚
∙coveredfloor mould 盖箱地面铸型
∙cylinder mould machine 圆网造纸机
∙double-mould-broadridgingplough 双壁起垄犁
∙draw mould 薄壁模子
∙driel mould 干型
∙drip mould 滴水线脚
∙drysand mould 干型
∙ear mould 耳模
∙electricpole mould hanger 电杆模型吊架
∙end mould 端模
∙Erical mould 可压锭模;挤压锭模
∙evacuated mould 空腔模
∙face mould 面模
∙fallwheatsnow mould 冬小麦雪霉病
∙falling mould 曲型线条
∙female mould 阴模
∙fixed mould 固定模
∙flaskless mould 无箱铸型
∙floating-point mould 浮点模型
∙floor mould 地铸模
∙fluted mould 波形模
∙foamsponge mould 泡沫胶硫化模
∙footed mould 压印底圈的模型
∙forging mould 锻模
∙front mould 前模
∙full-mould castingprocess 实型铸造
∙gang mould 成组模;成组模板
∙garden mould 园土
∙getinthe mould 垫平铸型
∙glass mould 玻璃型;玻璃铸型
∙glass mould diode 玻璃模二极管
∙graphite mould 石墨型
∙grass mould 腐草土
∙gray mould 灰霉
∙green mould 绿霉病
∙green mould ofcitrus 柑桔绿霉病
∙ground mould 地面铸型;堆土木模
∙gypsum mould 石膏型
∙hair mould 毛霉
∙hair mould sprout 毛霉芽
∙half mould 半型
∙hoistfor mould boardcarrier 模板车升降机
∙hump mould 压坯用阳模
∙ice mould 冰铸
∙ingot mould 钢锭模;铸锭模;铸锭型;锭模
∙ingot mould millingmachine 钢锭模铣床
∙ingotslab mould 扁钢锭模
∙insulating mould coating 隔热涂料
∙integral mould 整模型
∙invested mould 熔模铸型
∙iron mould 铁锈迹
∙leaf mould 叶霉;腐叶土
∙loam mould 泥型
∙lower mould half 下模;凹模
∙male mould 凸模;阳模
∙master mould 母型;原模
∙mismatchin mould 铸型错箱
∙mould 印模;模;模板;模具;模筛样板;模塑;模子;成型模具;圆网;造型模板;塑模;霉;霉病;霉菌;纸型
∙mould addition 钢锭模添加剂
∙mould anddiemillingmachine 模具铣床
∙mould assembling 合箱
∙mould assemblingandclosing 铸型合箱
∙mould assembly 合型
∙mould blower 吹型机
∙mould board 造型板;样板
∙mould boardlessplough 无壁犁
∙mould buggy 钢锭模车
∙mould case 模制壳
∙mould clamp 卡具
∙mould clamps 模型紧固夹
∙mould cleaner 模具清洁剂
∙mould closer 合箱机;合箱装置
∙mould coatingmaterial 钢锭模涂料
∙mould core 模芯
∙mould cover 腐殖质层
∙mould cure 模塑硫化;模型硫化
∙mould damagedsweetpotatopoisoning 黑斑甘薯中毒
∙mould dimension 铸型尺寸
∙mould drag 下半箱
∙mould drying 铸型烘干
∙mould efficiency 模塑效率
∙mould emptier 脱模机构
∙mould erosion 铸型冲蚀
∙mould facing 涂料
∙mould fitter 合箱工
∙mould flatgauge 样板
∙mould form 模型型腔
∙mould fungus 霉菌
∙mould growthtest 长霉试验
∙mould half 半型
∙mould hardness 铸型硬度
∙mould impression 模型内腔;模型型腔;模穴
∙mould inasnapflask 无箱造型
∙mould inthepit 地坑造型
∙mould inoculation 型内孕育
∙mould jacket 型套
∙mould kernel 模芯
∙mould life 模型寿命
∙mould lifting 铸型起模
∙mould lining 坩埚衬里
∙mould loft 放样间
∙mould loftfloor 放样台
∙mould lofter 放样工;放样工人
∙mould loftsman 放样工;放样工人
∙mould machine 模塑机
∙mould machineofcerealseedselection 谷物选种机
∙mould mark 模缝条痕
∙mould matrixcathode 模制阴极
∙mould oil 脱模油
∙mould onend 垂直分型造型
∙mould pigiron 型铁
∙mould plaster 模型用石膏
∙mould plate 模型板
∙mould plunger 阳模
∙mould plungerforceplug 凸模
∙mould preparationbay 钢锭模准备跨
∙mould press 模压机
∙mould pressing 旋压成形
∙mould proofing 防霉
∙mould rains 梅雨
∙mould release 分型粉
∙mould relese 脱模
∙mould rolloverunit 翻箱装置
∙mould sand 型砂
∙mould seam 模缝
∙mould setting-and-strippingbay 钢锭模准备和脱锭跨
∙mould shift 错箱
∙mould shrinkage 模内收缩;模压收缩;脱模后的收缩
∙mould splits 模组分
∙mould stripping 铸型起模;拆模
∙mould susceptibility 感霉性
∙mould testchamber 霉菌试验箱
∙mould train 模组
∙mould turnover 翻箱
∙mould unloading 出模;脱模;卸模
∙mould veining 铸型裂纹
∙mould vibrator 模板振动器
∙mould vulcanization 模塑硫化
∙mould wash 脱模涂料
∙mould washmixer 涂料搅拌机
∙multiplecavity mould 多型腔铸型;多巢模
∙multiple mould 多件石膏模
∙multiple-part mould 多箱铸型
∙needle mould 针模
∙one-piece mould 整体铸型
∙openbottom mould 底开式钢锭模
∙open mould 明浇铸型;敞口铸型
∙opensand mould 明浇砂型
∙opticalinstrument mould andfogauto-detector 光学仪器霉雾自动检测仪
∙ornamental mould 艺术造型
∙palletconveyer mould machine 滑板输送式造型机
∙paper mould 纸型
∙paste mould 衬碳模
∙paste mould ware 衬碳模成形的制品
∙peat mould 泥炭土
∙permanent mould 永久铸型
∙pig mould 锭模
∙plural mould operation 多模操作
∙porous mould 多孔模型
∙positive mould 阳模;阳压模
∙press mould 压模
∙press mould ware 模压器皿
∙pressing mould 压模
∙processofunconventionalheattreatmentof mould 模具非常规热处理工艺
∙quadrant mould 四开木压条
∙real mould 实模型
∙rectalsuppository mould 肛门栓剂模
∙refractoryshell mould 耐火材料壳型
∙removalofthe mould 拆模
∙reverse mould 倒模;倒型
∙revesingpermanent mould 双面金属型
∙ring mould 瓶颈模
∙ring-shaped mould 环型铸模
∙riskof mould 发霉险
∙roastsand mould 干砂型
∙rubber mould 橡胶皮模
∙running mould 模筛样板;模饰样板
∙saccharifying mould 糖化霉
∙sealingofa mould 铸型密封
∙section mould 型模
∙sectional mould 镶合砂型
∙semi-automatic mould 半自动模;半自动塑模
∙semi-chilled mould casting 半金属型铸造;半冷模铸造
∙semi-permanent mould 半永久型;半永久性模
∙semiclosedtop mould 半封顶锭模
∙shell mould machine 壳型造型机
∙shiftable mould-board 可拆换的刀片
∙sign mould 符号模型
∙singlecavity mould 整体铸型
∙single mould 单件模型
∙skindried mould 面干铸型
∙skindrying mould 表干型
∙sleepersteel mould 轨枕钢模
∙slime mould 粘菌
∙slipflask mould 脱箱铸型
∙snapflask mould 活箱造型;无箱铸型
∙snapflask mould 脱箱造型
∙snow mould 雪霉病;雪疫病
∙soap mould 皂模
∙sooty mould 烟霉;煤污病
∙sooty mould ofriceplant 水稻煤病
∙sooty mould oftea 茶叶煤污病
∙spacing mould 隔膜
∙split mould 对开模
∙stagnant mould 不动模型
∙standardsteelingot mould 标准钢锭模
∙steel mould 钢锭模;钢模
∙steel mould forelectricpole 电杆钢模
∙stock mould 定型模
∙stripper-plate mould 脱模板塑模
∙sweepingloam mould 刮泥型
∙swellofa mould 胀砂
∙symbol mould 符号模型
∙tapeof mould 模型锥度
∙thin-walledmetal mould 薄壁金属型
∙thin-walled mould 薄壁结晶器
∙three-cavity mould 三开箱铸型
∙tilt-mould billet 可倾模锭坯
∙tirerecapping mould 轮胎翻修硫化机
∙tomatoleaf mould 番茄叶霉病
∙top mould half 凸模
∙two-cavity mould 双型腔铸型
∙variable-point-mould 变点模型
∙vegetable mould 腐殖土
∙verge mould 山墙檐口线脚
∙waste mould gypsum 废模石膏
∙watch-case mould 表壳式压模
∙water mould 水霉
∙woodcasting mould 木质铸造模型
∙X-mould machine 多模成型机
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 模具术语 中英文翻译 模具 术语 中英文 翻译