电梯基础知识1 曳引式电梯.docx
- 文档编号:10793693
- 上传时间:2023-02-22
- 格式:DOCX
- 页数:50
- 大小:245.80KB
电梯基础知识1 曳引式电梯.docx
《电梯基础知识1 曳引式电梯.docx》由会员分享,可在线阅读,更多相关《电梯基础知识1 曳引式电梯.docx(50页珍藏版)》请在冰豆网上搜索。
电梯基础知识1曳引式电梯
1曳引式电梯
Tractionlift
电梯是一种机电结合紧密地用电力拖动的特殊升降设备,是一种现代生活中必不可少的,广泛应用的垂直交通运输工具,在现代城市文明中,电梯不但已成为高层建筑不可缺少的垂直运输设备,也将成为低层建筑中的代步工具。
在垂直交通运输工具中曳引式电梯是使用最普遍的一种电梯。
因此,本文以介绍曳引式电梯为主。
Beingaspecialsystemmovingupwardsanddownwardsbycombiningmechanicsandelectrics,lifthasplayedanindispensableroleinourmodernlifebyservingaswidely-usedvehiclethatrunsvertically;itisnotonlyanimportantverticalvehicleforhigh-risebuildings,butforlow-risingbuildings.
Asaverticalvehicle,tractionliftisthemostcommonlyusedlift;therefore,thefollowingdescriptionwillbebasedontractionlift.
1-1电梯的基本结构
Liftbasicstructure
1-1-1曳引系统
Tractionsystem
曳引系统主要由曳引机、曳引钢丝绳、导向轮及反绳轮等组成。
Tractionsystemiscomposedoftractionmachine,tractionrope,diverterpulleyandcounterweightsheave.
1-1-1-1曳引机有驱动电动机、制动器、减速箱、机座、曳引轮等组成。
它是电梯的动力源。
驱动电动机为电梯专用交流电机或直流电机。
Asthepowerprovider,tractionmachineiscomposedofdrivemotor,brake,gearedmachine,machinebaseandtractionsheave.DrivemotorisACorDCmotorforlift.
制动器通常采用双瓦块常闭式电磁制动器。
电梯停止或电源断电情况下制动抱闸,以保证电梯不致移动。
Usuallyadoptedisdoublelinednormallyclosedmagneticbrake.Brakeisactivatedtopreventliftfrommovingincaseofliftstoporpowerfailure.
减速机大多选用蜗轮蜗杆减速机,也有行星齿轮、斜齿轮减速机。
无齿轮电梯不需减速机。
曳引轮即为曳引机上的绳轮,两端借助曳引钢丝绳分别悬挂轿厢和对重。
Usuallyadoptediswormgearedmachine,besides,stargearandslantinggearedmachinearealsoavailable.Gearlessliftneedsnogearedmachine.Tractionsheaveisasheaveontractionmachine,onbothsidesofwhichcansuspendcarandcounterweightbymeansoftractionrope.
1-1-1-2曳引钢丝绳的两端分别连接轿厢和对重(或两端固定在机房上),依靠钢丝绳与曳引轮绳槽之间的静摩擦力来实现电梯轿厢的升降。
Bothsidesofthetractionropeareconnectedwithcarandcounterweight(orbothsidesareattachedtothemachineroom).Carismovedupwardsordownwardsbymeansofstaticfrictionbetweentractionropeandropegroove.
1-1-1-3导向轮又称抗绳轮,因电梯轿厢尺寸一般都比较大,轿厢悬挂中心和对重悬挂中心间的距离往往大于设计上所允许的曳引轮直径,因此对一般电梯而言需要设置导向轮,以保证两股向下的曳引钢丝绳之间的距离等于或接近轿厢悬挂中心和对重悬挂中心之间的距离,以分开轿厢和对重的间距。
DeflectorsheaveisalsocalledbeamPulley.Sincecariscomparativelylargeindimensions;thedistancebetweencarsuspensioncenterandcounterweightsuspensioncenterisgenerallylongerthanthediameteroftractionsheave,deflectorsheaveisusuallyusedforliftstoensurethedistancebetweentworopesdownwardstobeequaloralmostequaltothedistancebetweencarsuspensioncenterandcounterweightsuspensioncenter,distancingcarandcounterweight.
对复绕的无齿轮电梯而言,改变复绕轮的位置同样可以达到上述目的。
采用复绕轮还可以增加曳引能力。
Forgearlessliftwithcompoundwounding,changingthepositionofwindingpulleycanalsoachievetheabovepurpose,besidestheapplicationofcompoundwindingpulleycanalsoincreasetractioncapacity.
1-1-1-4反绳轮当钢丝绳的绕绳比大于1时,在轿厢顶和对重架上应增设反绳轮。
反绳轮的个数与曳引比有关,可以是1个、2个甚至是3个。
Diversionsheave:
withsuspensionratio>1,diversionsheaveshouldbeinstalledonthetopofcarandcounterweightframe.Relatedtosuspensionratio,numberofdiversionsheavecanbe1,2oreven3.
1-1-2导向系统
Divertersystem
导向系统由导轨、导靴(图1-3)和导轨架(图1-4)等组成。
它的作用是限制轿厢和对重的活动自由度,使轿厢和对重只能沿着导轨做升降运动。
Composedofguiderails,guideshoesandrailframe,divertersystemisusedtolimittheflexibilityofcarandcounterweight,makingcarandcounterweightmovealongtheguiderailupwardsanddownwards.
导轨固定在导轨架上,导轨架是支撑导轨的组件,与井道壁联接。
Guiderailsarefixedontherailframethatisusedtosupportrailsandconnectedwithwellwall.
导靴装在轿厢和对重架上,与导轨配合,强制轿厢和对重的运动服从于导轨的走向。
Installedoncarandcounterweightframe,guideshoesareworkingtogetherwithguiderails,forcingcarandcounterweighttomoveincompliancewiththedirectionofguiderails.
1-1-3门系统
Doorsystem
门系统由轿厢门、层门、门机、联动机构、门锁等组成。
Doorsystemiscomposedofcardoor,leveldoor,dooroperator,interconnectionanddoorlock.
轿厢门设在轿厢入口,有门扇、门导轨架、门靴和门刀等组成。
Locatedintheentrancetocar,cardooriscomposedofdoorfan,doorguiderailframe,doorshoeanddoorvane.
层门设在层站入口,有门扇、门导轨架、门靴、门锁装置及应急开锁装置组成。
Locatedintheentrancetolanding,landingdooriscomposedofdoorfan,doorguiderailframe,doorshoe,doorlockandemergencyunlockingdevice.
门机设在轿厢上,是轿门和层门开启和关闭的动力源。
Installedonthecar,dooroperatorispowerproviderforopeningandclosingcardoorandlandingdoor.
1-1-4轿厢
Car
轿厢是用以运送乘客或货物的电梯组件。
它是由轿厢架和轿厢体组成。
Composedofcarframeandcarbody,carisusedtoconveypassengersorcargo.
轿厢架是轿厢体的承重架构,由上横梁、立柱、底梁和斜拉杆等组成。
Asasupportforcarbody,carframeiscomposedoftoptransom,sidetransom,bottomtransomandbracerod.
轿厢体由轿厢底、轿厢壁、轿厢顶及照明、通风装置、轿厢装饰件和操纵盘等组成。
轿厢的大小由额定载重量和额定载客量决定。
Carboyiscomposedofcarbottom,carwall,cartop,ventilation,decorationprofileandcontrolpanel.Cardimensionsaredeterminedbyratedloadandpassengerflow.
1-1-5重量平衡系统
Weightbalancesystem
该系统由对重和重量补偿装置组成。
Suchsystemiscomposedofcounterweightandweightcompensationdevice.
对重由对重架和对重块组成。
对重将平衡轿厢自重和部分的额定载重。
Counterweightiscomposedofcounterweightandcounterweightfiller.Counterweightisusedtooffsetcarweightandpartialratedload.
重量补偿装置是补偿高层电梯中轿厢与对重侧曳引钢丝绳长度变化对电梯平衡影响的装置。
Weightcompensationdeviceisusedtooffsettheinfluenceontheliftbalancearisingfromthechangingropelengthofcarandcounterweight.
1-1-6电力拖动系统
Electricaldrivingsystem
该系统由曳引电机、供电系统、速度反馈装置、调速装置等组成。
对电梯实行速度控制。
Composedoftractionmachine,powersupplysystem,speedfeedbackdeviceandspeed-adjustingdevice,suchsystemisusedtocontrolliftspeed.
曳引电机是电梯的动力源,根据电梯配置可用交流电机或直流电机。
Tractionmachineisthepowerproviderforlift.ACorDCmotorcanbeselectedbasedonliftconfiguration.
供电系统是为电机提供电源的装置。
Powersupplysystemprovidespowerformotor.
速度反馈装置是为调速系统提供电梯运行速度信号。
一般采用测速发电机或速度脉冲发生器,与电机相连。
Speedfeedbackdeviceisusedtoprovideliftspeedsignalforspeed-adjustingsystem.Connectedwithmotor,tachogeneratororspeedpulsegeneratorisusuallyadopted.
调速装置对曳引电机实行调速控制。
Speedadjustingdeviceisusedtocontrolspeedoftractionmotor.
1-1-7电气控制系统
Electricalcontrolsystem
电气控制系统由操纵装置、位置显示装置、控制装置、平层装置、选层器等组成。
它的作用是对电梯的运行实行操纵和控制。
Composedofoperationdevice,positionindicatordevice,controldevice,levelingdeviceandselector,electricalcontrolsystemisusedtooperateandcontrollift.
操纵装置包括轿厢操纵盘或手柄开关箱、层站召唤按钮、轿顶和机房中的检修或应急操纵箱。
控制装置安装在机房中,由各类电气控制元件(或板)组成,是电梯实行电气控制的集中组件。
Operationdeviceiscomposedofoperationpanelorhandleswitchtank,landingcallbutton,inspectionoremergencycontrolbox.Installedinthemachineroom,astheintegratedunitforelectricalcontrol,controldeviceiscomposedofelectricalcontrolcomponents(orpanels).
位置显示装置裝在轿厢内和大厅内,显示电梯的运行层站和方向及载客量等信息。
Positionindicatorisinstalledincarandlanding,indicatingsuchinformationasliftrunninglanding,directionandpassengerflow.
选层器可由机械式、继电器或电子式组成,起指示和反馈轿厢位置、决定运行方向、发出减速信号等作用。
Havingmechanic,relayorelectronictypes,selectorisusedtoindicateandfeedbackcarposition,determinerunningdirectionandgiveoutreductionsignal.
1-1-8安全保护系统
Safetyprotectionsystem
电梯上设有机械和电气各类保护系统,以保证电梯安全使用。
Liftisequippedwithmechanicandelectricalprotectionsystemstoensureliftsafeoperation.
机械方面有限速器、安全钳、缓冲器、渐进式行程开关等。
Mechanicaldevicesincludeoverspeedgovernor,safetygear,bufferandprogressivetravelswitch.
电气方面设有一系列安全开关保护电梯的各个运行环节,例如,电源断路保护器,轿顶急停开关,底坑急停开关,极限开关,紧急出口接点,超速保护开关,安全钳开关,门保护开关,检修开关等。
Electricaldevicesincludeaseriesofsafetyswitchestoprotecteveryoperationstages,suchaspowercut-offprotector,emergencystopswitchontopofthecarandinthepit,limitswitch,emergencyexitcontact,overspeedprotectionswitch,safetygearswitch,doorprotectionswitchandinspectionswitch.
1-2电梯的分类
Lifttypes
电梯的定义:
用电力拖动的轿厢运行于铅垂的或与铅垂方向倾斜不大于15o的两列刚性导轨之间运送乘客或货物的固定设备。
目前不论其驱动方式如何,将电梯作为建筑物内垂直交通运输工具的总称。
Liftisdefinedasafixeddevicethathoistsacartravelingverticallyornotexceeding15°verticallybetweentworigidrails,toconveypassengersorcargo.Whateverdrivetypelifthas,itisacollectivetermforvehicletravelingwithinabuilding.
根据建筑物的高度、用途及客流量(或物流量)不同,而设置不同种类的电梯。
目前电梯的基本分类方法大致如下:
Basedonthebuilding’sheight,applicationandpassengerflow(orcargoflow),differenttypesofliftsareused.Currently,liftsareclassifiedbasedonthefollowingcriteria:
1-2-1按驱动方式分类
Classifiedbydrivetype
1-2-1-1交流电梯
AClift
用交流感应电动机作为驱动力的电梯。
根据拖动方式又可分为交流单速、交流双速、交流调压调速、交流调频调压调速电梯。
ACmotorisusedinlift.Basedontractiontypes,liftscanbeclassifiedasACsingle-speed,ACdouble-speed,ACspeed/voltage-viable,ACviablespeed/frequencylifts.
1-2-1-2直流电梯
DClift
用直流电动机作为驱动力的电梯,这类电梯的额定速度都在2m/s以上。
DCmotorisusedinliftwhoseratedspeedisabove2m/s.
1-2-1-3液压电梯
Hydrauliclift
利用电动泵驱动液体流动,由柱塞使轿厢升降的电梯。
Bymeansofelectricalpumpdrivingfluid,liftismovedupwardsordownwardsthroughplunders.
1-2-1-4齿轮齿条电梯
Gearracklift
将导轨加工成齿条,轿厢装上与齿条啮合的齿轮,电动机带动齿轮旋转使轿厢升降的电梯。
Railsaremadeintogearracks.Carisequippedwithgearsthatareengagedwithracks.Liftismovedupwardsordownwardsbymeansoftherotationofgearsdrivenbymotor.
1-2-1-5螺杆式电梯
Spiralleverlift
将直顶式电梯的柱塞加工成矩形螺纹,再将带有推力轴承的大螺母安装于油缸顶,然后通过电机经减速机(或皮带)带动大螺母旋转,从而使螺杆顶升轿厢上升或下降的电梯。
Inspirallevellifts,plundersofstraightly-pushedliftsaremadeintorectangularthreads;bignutswithpushingbearingsareinstalledonthetopofthecylinder.Throughmotor,thebignutsrotatewithgearedmachine(orbelt).Therefore,supportedbythespirallever,liftscanmoveupwardordownwards.
1-2-1-6直线电机驱动的电梯
Machinedrivenbylinealmotor
其动力源是直线电机。
Liftispoweredbylinealmotor.
1-2-2按用途分类
Classifiedbyapplications
1-2-2-1乘客电梯
Passengerlift
为运送乘客设计的电梯,要求有完善的安全设施及一定的轿厢内装饰。
Passengerliftisdesignedtoconveypassengersandrequiredtohaveperfectsafetyfacilitiesandnecessarydecorationinthecar.
1-2-2-2载货电梯
Cargolift
主要为运送货物而设计的电梯,有司机载货电梯允许司机及装卸人员随同上下;无司
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 电梯基础知识1 曳引式电梯 电梯 基础知识 曳引式